background image

Page 5 

 

Description 

The PC120 Paddock Cleaner is designed to pick up horse dung and other debris with ease to make paddock 
maintenance quick and easy. 

 

The PC120 Paddock Cleaner is a trailed attachment, with 4 Polyethylene brushes powered by a Honda GX200 6.5hp 
Engine collecting dung into a 550 (approx.) litre hopper. The engine comes with easy electric start and optional 
remote throttle cable, allowing the installation of the throttle on the back of a Quad should it be required. 

 

The PC120 also comes with a unique remote electric tipping mechanism that allows for easy emptying of the 
hopper by a simple controller.  

 

These machines should however only be used to perform tasks for which they were designed - use of the machine 
for any other function may be both dangerous to persons, and potentially damaging to components. Use of the 
machine beyond the stated usage may invalidate any applicable warranty, as well as being potential in breach of 
applicable safety regulations. 

 

 

Identification 

Each machine is fitted with a serial plate (shown below) which details the following: 

 

1.

 

Model 

2.

 

Date of Manufacture (DOM) 

3.

 

Serial Number 

4.

 

Mass 

 

When enquiring regarding spares or additional 
equipment, ensure you have this information to hand. 

 

 

Noise Levels 

 

The sound of this machine, as measured at the typical operator location under normal operating conditions, is 91db. 
If being towed by an open-cab vehicle, it is 

essential 

that ear defenders or a suitable helmet is worn at all times. If 

being towed behind a closed-cab UTV, 4x4 or similar, then the cab should remain closed to reduce noise. 

 

Ear defenders or other suitable protection should be worn at all times when 

operating 

Содержание PC120

















Отзывы: