manualshive.com logo in svg

Chaparral VFS226, Руководство пользователя

Поделиться
Скачать
Chaparral VFS226 Скачать руководство пользователя страница 47

 

Configuring the Router

3-17

9

Select 

Yes

 and press 

Enter

 to make the changes.

The system confirms that the changes are made. 

10

Press 

Enter

 to return to the Host Configuration Menu.

Changing the SCSI ID Assigned to Each Router 
Channel

The router assigns each of its SCSI channels one of the SCSI IDs (initiator IDs), leaving 
15 SCSI IDs available for devices. You can change the SCSI ID assigned to each SCSI 
channel.

To change the SCSI ID assigned to a SCSI channel:

1

From the System Menu, select 

Configuration

 

Menu

 and press

 Enter

.

The Configuration Menu screen displays. 

2

Select 

Channel Configuration

 and press

 Enter

.

The Channel Configuration screen displays. 

Note: 

If you change the topology, FC Link Speed, Loop ID, or router 

LUN, you must reboot the router for the change to take effect. See 

Rebooting the Router on page 3-23

. If you entered a specific Loop ID or 

LUN, check it to see if the current setting is what you entered. If the Loop 
ID or LUN is not what you want, change it again.

Содержание VFS226













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды