background image

100402 - 2000W DUAL FUEL INVERTER GENERATOR

IMPORTANT SAFETY INSTRUCTIONS

6

Fuel Safety

 

DANGER

GASOLINE, GASOLINE VAPORS AND PROPANE (LPG) ARE 
HIGHLY FLAMMABLE AND EXPLOSIVE.

Fire or explosion can cause severe burns or death.

Gasoline and gasoline vapors:

 

Gasoline is highly flammable and explosive.

 

Gasoline can cause a fire or explosion if ignited.

 

Gasoline is a liquid fuel but it’s vapors can ignite.

 

Gasoline is a skin irritant and needs to be cleaned up 
immediately if spilled on skin or clothes.

 

Gasoline has a distinctive odor, this will help detect potential 
leaks quickly.

 

In any petroleum gas fire, flames should not be extinguished 
unless by doing so the fuel supply valve can be turned OFF. 
This is because if a fire is extinguished and a supply of 
fuel is not turned OFF, then an explosion hazard could be 
created.

 

Gasoline expands or contracts with ambient temperatures. 
Never fill the gasoline tank to full capacity, as gasoline 
needs room to expand if temperatures rise.

LPG:

 

LPG is highly flammable and explosive.

 

LPG is under pressure and can cause a fire or explosion if 
ignited.

 

LPG is heavier than air and can settle in low places while 
dissipating.

 

LPG has a distinctive odor added to help detect potential 
leaks quickly.

 

In any petroleum gas fire, flames should not be extinguished 
unless by doing so the fuel supply valve is turned OFF. This 
is because if a fire is extinguished and a supply of fuel is not 
turned OFF, then an explosion hazard could be created.

 

When exchanging LPG cylinders, check that the cylinder 
valve is of the same type.

 

Always keep the LPG cylinder in an upright position.

 

LPG will burn skin if it comes in contact with it. Keep any 
and all LPG away from skin at all times.

When adding or removing gasoline:

DO NOT light or smoke cigarettes.

Turn the generator off and let cool for at least two minutes 
before removing the gasoline cap. Always loosen the cap slowly 
to relieve pressure in the tank.

Only fill or drain gasoline outdoors in a well-ventilated area.

DO NOT pump gasoline directly into the generator at the gas 
station. Always use an approved container to transfer the fuel to 
the generator.

DO NOT overfill the gasoline tank.

Always keep gasoline away from sparks, open flames, pilot 
lights, heat and other sources of ignition.

When starting the generator:

DO NOT attempt to start a damaged generator. 

Always check that the gasoline cap, air filter, spark plug, fuel 
lines and exhaust system are properly in place.

Always allow spilled gasoline to evaporate fully before 
attempting to start the engine.

Always be certain that the generator is resting firmly on level 
ground.

When operating the generator:

DO NOT move or tip the generator during operation.

When transporting or servicing the generator:

Always check that the fuel valve is in the OFF position and the 
gasoline tank is empty.

For LPG compatible models, check that the LPG cylinder is 
disconnected and stored securely away from the generator.

Disconnect the spark plug wire.

When storing the generator:

Store away from sparks, open flames, pilot lights, heat and 
other sources of ignition.

Do not store generator, gasoline or LPG cylinders near furnaces, 
water heaters, or any other appliances that produce heat or 
have automatic ignitions.

 

DANGER

NEVER place a gasoline container, gasoline tank, LPG cylinder 
or any combustible material in the path of the exhaust stream 
during operation of the engine.

 

WARNING

Never use a gasoline container, gasoline tank, LPG connector 
hose, LPG cylinder or any other fuel item that is broken, cut, 
torn or damaged.

Содержание 100402


































Отзывы: