background image

100402 - 2000W DUAL FUEL INVERTER GENERATOR

STORAGE

26

5.  Insert the small spring back into the pocket of the upper 

cover and press the upper cover into place to complete the 
installation. 

Adjusting the Governor

 

WARNING

Tampering with the factory set governor will void your 
warranty.

The air-fuel mixture is not adjustable. Tampering with 
the governor can damage your generator and your 
electrical devices and will void your warranty. Contact our 
Technical Support Team at 1-877-338-0999 for all other 
service and/or adjustment needs.

Maintenance Schedule

Follow the service intervals indicated in the following 
maintenance schedule. 
Service your generator more frequently when operating in 
adverse conditions. 
Contact our Technical Support Team at 1-877-338-0999 
to locate the nearest CPE certified service dealer for your 
generator or engine maintenance needs.

EVERY 8 HOURS OR DAILY

 

—

Check oil level

 

—

Clean around air intake and muffler

FIRST 5 HOURS

 

—

Change oil

EVERY 50 HOURS OR EVERY SEASON

 

—

Clean air filter

 

—

Change oil if operating under heavy load or in hot 
environments

EVERY 100 HOURS OR EVERY SEASON

 

—

Change oil

 

—

Clean/adjust spark plug

 

—

Check/adjust valve clearance*

 

—

Clean spark arrestor

 

—

Clean fuel tank and filter*

EVERY 250 HOURS

 

—

Clean combustion chamber*

EVERY 3 YEARS

 

—

Replace fuel line*

* To be performed by knowledgeable, experienced owners or CPE certified 

service centers.

STORAGE

 

DANGER

Gasoline and gasoline vapors are highly flammable and 
extremely explosive.

Fire or explosion can cause severe burns or death. Only 
fill or drain fuel outdoors in a well-ventilated area. DO NOT 
pump gasoline directly into the generator. Use an approved 
container to transfer the fuel to the generator. Never use 
a gasoline container, gasoline tank, or any other fuel item 
that is damaged or appears damaged. DO NOT overfill the 
gasoline tank. Always keep fuel away from sparks, open 
flames, pilot lights, heat and other sources of ignition. 
DO NOT light or smoke cigarettes.

Short Term Storage (up to 1 year)

Gasoline in the gasoline tank has a maximum shelf life of up to 
1 year with the addition of properly formulated fuel stabilizers 
and if stored in a cool, dry place. Gasoline in the carburetor, 
however, may gum up and clog the carburetor if it isn’t used or 
drained within 2-4 weeks.

Содержание 100402


































Отзывы: