Chamberlain MyQ 889LM Скачать руководство пользователя страница 1

Страница: 1 / 12

MyQ

CONTROL PANEL

MODEL 889LM

To prevent possible SERIOUS INJURY or DEATH from electrocution:
•  Be sure power is NOT connected BEFORE installing door control.
•  Connect ONLY to 7-28 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
•   Install door control within sight of garage door, out of reach of children at a

minimum height of 5 feet (1.5 m) above floors, landings, steps or any other
adjacent walking surface, and away from ALL moving parts of door.

• NEVER permit children to operate or play with door control push buttons or

remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly adjusted, and

there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER permit

anyone to cross path of closing garage door.

• DO NOT install this door control on garage door opener systems controlling

one-piece or swing doors.

To provide an adequate visual alert, the garage door opener light bulb(s) MUST
be a minimum of 40 Watt (or equivalent).

The MyQ Control Panel is intended to be installed with S

Garage Door

Openers manufactured between 1998 and present. The MyQ Control Panel is NOT
compatible with S 2.0

Garage Door Openers. DO NOT install this door

control on garage door opener systems controlling one-piece or swing doors.

APPLICATION

The MyQ Control Panel offers a quick and convenient way to add S 2.0 and
MyQ technology to your existing garage door opener. MyQ technology uses a
900MHz signal to provide two-way communication between the garage door
opener and MyQ enabled accessories. When programmed to the LiftMaster

Internet Gateway you can monitor and control your garage door from any internet
enabled computer or smartphone. You may program up to 12 S 2.0
remote controls, 2 S 2.0 keyless entries and a combination of 16 MyQ
accessories to the MyQ control panel.

COMPATIBLE ACCESSORIES

S 2.0

Accessories:

MyQ Accessories:

Model 891LM
1- Button Remote Control

Model 823LM
Remote Light Switch

Model 893LM
3-Button Remote Control

Model 825LM
Remote Light Control

Model 890MAX
3-Button Mini MAX Remote Control

Model 828LM
LiftMaster

Internet Gateway

Model 893MAX
3-Button MAX Remote Control

Model 829LM
Garage Door and Gate Monitor

Model 895MAX
3-Button Premium MAX Remote Control

Model 877LM
Wireless Keyless Entry

Model 877MAX
Wireless MAX Keyless Entry

OVERVIEW

Install the MyQ Control Panel in place of the existing door control, within sight of
garage door, out of reach of small children at a minimum height of 5 feet (1.5 m)
above floors, landings, steps or any other adjacent walking surface, and away from
ALL moving parts of door. Due to power consumption the MyQ Control Panel
cannot be used in conjunction with another wired door control connected to your
garage door opener. If an additional door control is needed, the

wireless door

control model 885LM

can be programmed to the MyQ Control Panel.

To program the 885LM to the MyQ Control Panel, follow the remote control
programming steps. When in battery back-up mode, any feature using unattended
operation such as Timer-to-Close, closure from a garage door and gate monitor or
remote operation utilizing the LiftMaster

Internet Gateway will be disabled.

1. Disconnect all electrical and battery power (if applicable) to the garage door

opener.

  2.  Remove the existing door control from the wall.
  3.   Note the polarity of the wires connected to the existing door control.

• Label the wire connected to the RED terminal.

• Label the wire connected to the WHITE terminal.

Disconnect the wires from the existing door control.

4. Connect the wires to the new MyQ Control Panel. Make sure the polarity is

correct.

• Red wire to the R terminal.

• White wire to the W terminal.

INSTALLATION