background image

"A"
B

u

tton

 

"B"
B

u

tton

 Bell 

W

ire

Terminal
Scre

w

s

RED

W

HT

-1

-2

Back Panel

KG

1

3

9

7

5

KG

1

3

9

7

5

Antenna

To release 

w

ire, p

u

sh

in ta

b

 

w

ith scre

w

dri

v

er tip

Q

u

ick-Connect

Terminals

11 mm

Strip 

w

ire 11 mm

Red

Grey

W

hite

Model 76LM

Lighted Door Control

Locate the door control within sight of the door at a minimum
height of 1.5 m where small children cannot reach, and away from
all moving parts of the door and door hardware.

Installing the Door Control

1. Strip 11 mm of insulation from one end of the bell wire. Connect

it to the two screw terminals on the back of the door control by
color: white wire to 2 and white/red wire to 1.

2. Remove the cover from the door control by pushing the bottom

of the cover up then outward. Fasten door control securely with
6ABx1-1/2" screws. If installing into drywall, drill 5/32" holes and
use the anchors provided.

3. Run the bell wire up the wall and across the ceiling to the motor

unit. Use insulated staples to secure the wire in several places.
Do not to pierce the wire with a staple, creating a short or open
circuit.

4. Strip 11 mm of insulation from end of bell wire. Connect the bell

wire to the quick-connect terminals as follows: white to white and
white/red to red (Figure 1).

NOTE: 

When connecting multiple door controls to the opener, twist

same color wires together. Insert wires into quick-connect holes:
white to white and red/white to red.

5. Use tacks or staples to permanently attach the entrapment

warning label to the wall near the door control, and the manual
release/safety reverse label in a prominent location on the inside
of the garage door.

To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is not connected BEFORE installing door control.
• Connect ONLY to 24 VOLT low voltage wires. 
To prevent possible SERIOUS INJURY or DEATH from a closing garage
door:
• Install door control within sight of garage door, out of reach of children

at a minimum height of 1.5 m, and away from all moving parts of door.

• NEVER permit children to operate or play with door control push

buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly adjusted,

and there are no obstructions to door travel.

• Always keep garage door in sight until completely closed. NEVER

permit anyone to cross path of closing garage door.

WARNING

CAUTION

WARNING

WARNING

ATTENTION

AVERTISSEMENT

AVERTISSEMENT

AVERTISSEMENT

Figure 1

Programming The Remote Control

Below are instructions for programming your operator to operate
with Security

®

remote controls.

1. Remove the cover from the door control. 

2. Press and hold the button on the hand-held

remote that you wish to operate your
garage door.

3. While holding the remote button, press and

hold the “A” button on the Lighted Door
Control.

4. Continue holding both buttons while you

press the “B” button on the Lighted Door
Control (all three buttons are held).

5. Release buttons when the motor unit lights

blink. It has learned the code. If light bulbs
are not installed, two clicks will be heard.

"A"
Button

"B"
Button

To Erase All Codes From Motor Unit Memory

To deactivate any unwanted remote, first erase
all codes:

Press and hold the “learn” button on motor unit
until the learn indicator light goes out
(approximately 6 seconds). All previous codes
are now erased. Reprogram each remote or keyless entry you wish
to use.

© 2006, The Chamberlain Group, Inc.

114A3222B

All Rights Reserved

Отзывы: