background image

WIRELESS KEYLESS ENTRY – MODEL SERIES 66 AND 740

FEATURES OF THE KEYPAD TRANSMITTER

Personalized Code: Up to 10,000 possible combinations.
Code can easily be changed if desired.

Operation:  Opener activates when 4-code digits and ENTER
button are pressed.

The Keypad Transmitter will open and close the door even if the
Door Control Lock Switch feature is ON. 

If wrong numbers are accidentally pressed, correction can be
made immediately. The ENTER key will transmit only the last
four digits.

The keypad will blink for 15 seconds after the code is 
transmitted. During that time, you can STOP or REVERSE door
travel just by pressing the ENTER key.

The keypad transmitter can be used with garage door opener
receivers having a yellow, grey, white or green “learn” button.

©2001, The Chamberlain Group

114A1401D

All Rights Reserved

Printed in Mexico

1. Press and release the “learn” button on motor

unit. The learn indicator light will glow steadily
for 30 seconds.

2. Within 30 seconds, enter a four digit personal

identification number (PIN) of your choice on
the keypad. Then press and hold the ENTER
button.

3. Release the button when the motor unit lights

blink. It has learned the code. If light bulbs are
not installed, two clicks will be heard.

KG

KG

1

3

9

7

5

1

3

9

7

5

1

2

3

1

2

Setting the Code

2

1

KG

Installation

Open the keypad cover
and remove the battery
compartment screw.
Take out the battery.
Note the battery 
polarity as marked on
compartment.
Follow the installation
instructions described
below.
1. Center the keypad at

eye level against the
selected location on
garage exterior as shown.

NOTE:  For a one-piece door on a
brick, stone or aluminum sided
garage, use the optional location
shown in the illustration to avoid injury
as the door swings up and out.

2. Hold keypad firmly with cover half

open so both the top and bottom
mounting holes are visible. Use a
punch to mark each hole. Drill two
1/8" pilot holes. Fasten securely
with screws provided.

3. Insert the plug provided into the top

hole to cover the fastening screw.
Return the battery, being sure to
observe polarity. Re-fasten compartment cover.

Door Jamb Edge
(Optional Location 
for 1-Piece Door)

Keypad

Door Jamb Face
SECTIONAL DOOR ONLY

KEYPAD MUST BE INSTALLED 
WITHIN SIGHT OF THE DOOR

Exterior Front Wall
1-Piece or 
Sectional Door

Typical 
Installation

Plug

Battery

Battery Cover

The Keyless Entry Battery

The 12 volt battery should produce power
for at least one year. Replace when the
keypad illumination becomes dim.

Dispose of old batteries properly.

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

WARNING

NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the 
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.

To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children.  NEVER

permit children to operate, or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door.

WARNING

FOR SERVICE DIAL OUR TOLL-FREE NUMBER:
1-800-654-4736

Отзывы: