manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 230

 

 

 

MAY 2019 

 

6. General Procedures/Information

 

6-16 

CMT-130TC Book Trimmer 

GP 6.15 Principles of Operation 

Configuration Options 

The CMT-130TC has five possible infeed config-
urations and three possible outfeed configura-
tions.   

The infeed options are:   

 

Inline (Tilt Infeed with Elevator) 

 

Pile Feeder 

 

 Pile Feeder 

 

Standard Hand Feed Conveyor 

 

Long Hand Feed Conveyor 

The outfeed options are:  

 

Vertical Book Stacker 

 

Exit Conveyor 

 

Exit Chute 

Sequence of Operations 

– Infeed 

Option 1: In-line (Tilt Infeed with Elevator) 

1.  A book is released from the binder and 

drops onto the infeed belts of the Tilt Infeed 
Conveyor.  A diffuse sensor detects that 
there is a book on this conveyor, signals to 
the computer to drive the book onto the tilted 
conveyor. 

2.  One of three possible retro-reflective sen-

sors on the tilt table detects the book, and 
then the tilt table drops to a level condition.  
The conveyor on the tilt table drives the 
book onto the level conveyor portion of the 
tilt conveyor.  The book passes over a re-
flector near the end of the conveyor near the 
input of the Elevator.  When the reflector be-
comes uncovered, the computer knows the 
book is completely in the Elevator.  Cables 

connect power and logic between the trim-
mer and the conveyor.  The logic controls 
the air valve used to actuate the tilt portion 
of the conveyor. 

3.  The Elevator has a retro-reflective sensor at 

the bottom of the Elevator that detects if the 
Elevator is empty or not.  This signals to the 
computer whether or not it is necessary to 
lift the shelves to the next position. 

4.  The Elevator has a retro-reflective sensor at 

the top aiming down toward a reflector on 
the top shelf.  This lets the computer know 
whether to push a book off the top shelves 
and into the trimmer, or to lift the shelves up 
to the next position.   

5.  A cylinder pushes the book into the ma-

chine.  A normally open, micro switch is ac-
tuated by the pusher at its home position.  
To protect the machine, the Elevator cannot 
increment if the pusher is not home.  The 
micro switch is wired in series with the inter-
lock switch on the Elevator door.  This con-
nection provides power to the Elevator mo-
tor and does not rely on logic to stop the El-
evator from lifting.  Logic wiring is run be-
tween an additional switch on each interlock.  
This logic data is communicated through the 
cable connecting the Elevator and infeed 
conveyor.  It is communicated to the trimmer 
through the cable connected between the 
Elevator and the trimmer. 

6.  The book is pushed across an intermediate 

shelf fastened to the left side of the trimmer.  
A retro-reflective sensor is mounted above 
the shelf, and detects when a book jams and 
does not completely evacuate from the Ele-
vator, thereby stopping the trimmer and 
showing a jam error on the screen.  

7.  There is a barcode scanner mounted to the 

intermediate shelf that scans barcodes on 
book covers as they enter the trimmer.  The 

information stored in the barcode may con-
tain dimensional data for the book to be 
trimmed. 

8.  The shelf also supports the book as it 

crosses the span between the Elevator 
shelves and the trimmer.   

Option 2: Pile Feeder 

1.  Books are stacked vertically with the spine 

side down on the loading table of the feeder.  
The table contains belts and a back stop 
that move the pile forward, until a retro-re-
flective sensor detects when a book is ready 
to be dropped onto the intermediate tilt ta-
ble. 

2.  When the Pile Feeder gets the signal from 

the computer to send a book to the trimmer, 
it drops one book at a time onto the interme-
diate tilt table.  A retro-reflective sensor de-
tects when a book is on the intermediate tilt 
table, and then the table drops down and 
delivers the book to the lower tilt table. 

3.  One of two possible retro-reflective sensors 

on the lower tilt table detects the book, and 
then the lower tilt table drops to a level con-
dition.  The conveyor on the tilt table drives 
the book toward the trimmer. 

4.  The book moves across an intermediate 

shelf fastened to the left side of the trimmer.  
A retro-reflective sensor is mounted above 
the shelf, and detects when a book jams and 
does not completely evacuate from the Pile 
Feeder, thereby stopping the trimmer and 
showing a jam error on the screen.  

5.  There is a barcode scanner mounted to the 

intermediate shelf that scans barcodes on 
book covers as they enter the trimmer.  The 
information stored in the barcode may con-
tain dimensional data for the book to be 
trimmed. 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды