manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 227

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

6-13 

6. General Procedures/Information

 

GP 6.12 Hirschmann Connectors 

Hirschmann connectors are used on all three hy-
draulic solenoid valves at the manifold and on 
the proportional air valve.  The following proce-
dure describes how to disassemble Hirschmann 
connectors to check for loose or shorted wires. 

Procedure 

1.  Switch the main power OFF and lockout 

power to the machine. 

2.  Using a small screwdriver, completely re-

move the mounting screw from the con-
nector. 

3.  Remove the Hirschmann connector from the 

solenoid by pulling the connector away from 
the solenoid. 

4.  Disconnect the strain relief nut on the end of 

the connector. 

5.  Pry the bottom of the connector out. 

6.  Push the cable into the connector to reveal 

the contacts. 

7.  Inspect the contacts for loose or shorted 

wires.  Re-connect wires as necessary. 

8.  Assemble and reinstall the connector. 

 

Figure 6-15. Hirschmann Connector 

 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды