Challenge 130TC-A-160000 Скачать руководство пользователя страница 129

Страница: 129 / 282

MAY 2019

CMT-130TC Book Trimmer

4-23

4. Repair/Adjustment Procedures

ADJ 4.18 Knife Latch

The proximity sensor on the knife latch may be
adjusted according to the following procedure.

Procedure

1. Switch the main power ON and press the

green start button to initialize trimmer. This
will raise the knife mechanism off the knife
latch if it had drifted down.

2. Go to the diagnostic screen (GP 6.2 In-

put/Output Diagnostics). This will assist in
the adjusting of the sensor by emitting an
audio beep whenever the sensor is activated
or deactivated.

3. Open the rear door to access the knife latch.

4. Loosen the proximity sensor mounting

screws.

5. Push the latch block all the way back until

the air cylinder is fully retracted.

6. Adjust the proximity sensor to within 0.010"

(0.03 mm) of the latch block. Use the audio
beep as an indicator of when the sensor is
activating properly

7. Tighten the proximity mounting screws,

making sure not to move the sensor while
tightening.

8. Close the rear door and replace the waste

bin.

Figure 4-35. Knife Latch

Содержание 130TC-A-160000



























































































































































































































































































Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Бренды по названию

Популярные бренды

Challenge 130TC-A-160000, Руководство по обслуживанию

Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Бренды по названию

Популярные бренды