manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 128

 

 

 

MAY 2019 

 

4. Repair/Adjustment Procedures

 

4-22 

CMT-130TC Book Trimmer 

ADJ 4.17 Knife Gib Adjustment 

The front side of the knife bar has two gibs that 
may occasionally require adjustment.  There is 
one gib on each end of the knife bar.  Perform  
ADJ 4.5 Accuracy Adjustment after adjusting the 
gibs. 

Procedure 

1.  Switch the main power OFF. 

2.  Move the waste bin aside and open the rear 

door. 

3.  Loosen all six jam nuts and gib screws. 

4.  Tighten the middle gib screw on each side of 

the knife bar.  Stop tightening the screws 
when they begin to feel tight and the gib is 
visibly against the knife bar. 

5.  Turn the screws counterclockwise enough to 

release any force on the knife bar but not 
enough to allow the gib to visibly move away 
from the knife bar. 

6.  Repeat steps 4 through 5 for the top and 

bottom gib screws on each end of the knife 
bar. 

7.  Securely lock the gib screws in place with 

their jam nuts.  Use a hex allen wrench to 
prevent the screws from turning as the jam 
nuts are tightened. 

8.  Close the door and replace the waste bin. 

9.  After adjusting gibs, it may be necessary to 

perform ADJ 4.5 Accuracy Adjustment. 

 

 

Figure 4-34. Gib Screws 

 

 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды