CGEO INTERNATIONAL LIMITED CGEO-SG5 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 16

CGEO INTERNATIONAL LIMITED CGEO-SG5 Скачать руководство пользователя страница 8

CGEO-SG5

Rebar VW Strain Gauge 7

CGEO INTERNATIONAL LIMITED

Installation Manual

Instrument Cables

Instrument Cable

Reinforcing Rebar

or Strand

Reinforcing Rebar

or Strand

Wire Tie

(2 places)

Rebar Strain Gauge

Rebar Strain Gauge

(3 places, 120° apart)

Wire Tie

Tied to Reinforcing Rebar

Tied to Reinforcing Rings

Figure 5 - Model CGEO-SG5 "Sister Bar" Installation Detail

2.3. Cable Installation

As noted in the installation sections, route the instrument cables along the structural rebar and
tie off using nylon cable ties every 2-3 feet (1 meter) to secure. Outside of the instrumented
structure, the cable should be protected from accidental damage caused by moving equipment or
other construction activity.

Cables may be spliced to lengthen them, without affecting gage readings. Always waterproof the
splice completely, especially when embedding within the concrete, preferably using an epoxy
based splice kit such the 3M Scotchcast , model 82-A1. These kits are available from the factory.

«
...
6
7
8
9
10
...
»

Содержание CGEO-SG5

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды