manualshive.com logo in svg

CGEO INTERNATIONAL LIMITED CGEO-SG5, Руководство по установке

Поделиться
Скачать
CGEO INTERNATIONAL LIMITED CGEO-SG5 Скачать руководство пользователя страница 11

CGEO-SG5

 

Rebar VW Strain Gauge                                                                                                                                        10 

CGEO INTERNATIONAL LIMITED 

                                                                              Installation Manual           

K is the thermal coefficient. 

Normally the effect of temperature to VW strain gauge is little, it needn’t to be corrected. Detail 
calculation method see calculation equation and related factor in calibration certificate. 

 

4.3. Environmental Factors 

 
Since the purpose of the Strain Gauge installation is to monitor site conditions, factors which 
may affect these conditions should be observed and recorded. Seemingly minor effects may 
have a real influence on the behavior of the structure being monitored and may give an early 
indication of potential problems. Some of these factors include, but are not limited to: blasting, 
rainfall, tidal or reservoir levels, excavation and fill levels and sequences, traffic, temperature 
and barometric changes, changes in personnel, nearby construction activities, seasonal changes, 
etc. 

 

Содержание CGEO-SG5

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды