CET PMC-1302 Скачать руководство пользователя страница 17

Страница: 17 / 20

CET Electric Technology

Appendix A - Technical Specifications

10/100BaseT Ethernet Port (P1)

Speed
Connector
Cable

10/100 Mbps
RJ45
CAT5, CAT5e with a maximum 100m distance

Serial Ports (P2, P3)

P2, P3
Baudrate

RS-485 (D+, D- SH)
1200/2400/4800/9600/19200/38400 bps

Front Panel LED Indicators

Run (Green)

Blinking - System is running normally

P2, P3 (Green)

Blinking - Receiving activity

P2, P3 (Yellow)

Blinking - Transmitting activity

Protocol

Protocol

TCP, UDP, HTTP

Power Supply (L/+, N/-)

Standard
Burden

95-250VAC/DC, 47-440Hz
<3W

Protection

ESD Protection
Isolation Protection

8kV
3kV for RS485
1.5kV for Ethernet Port

Environmental Conditions

Operating Temp.
Storage Temp.
Humidity
Atmospheric pressure

-25°C to +70°C
-40°C to +85°C
5% to 95% non-condensing
70 kPa to 110kPa

Mechanical Characteristics

Unit Dimensions
Shipping Weight
Shipping Dimensions
Mounting
IP Rating

72x65x95mm
TBD
TBD
DIN-Rail Mounting
20

Содержание PMC-1302





















Результаты поиска

Содержание PMC-1302

Отзывы:

Бренды по названию

Популярные бренды

CET PMC-1302, Руководство пользователя

Результаты поиска

Содержание PMC-1302

Отзывы:

Бренды по названию

Популярные бренды