background image

Instruction Handbook                          PFP-18hpVGD-MR-CE  

- 4 -

 

 C.E.T. Fire Pumps Mfg. This handbook is subject to change without notice, 

Contact your local C.E.T. dealer or C.E.T. direct to ensure you have the latest version.

 

2.

 

 

Safety instructions 

It  is  very  important  that  you  read  and  understand  this  handbook  and  the 
owner’s manual of the engine before you start the pump. 
 

o

 

NEVER run the engine in an enclosed area. Exhaust gases contain carbon 

monoxide which is an odorless and potentially deadly gas. You can run it if 

using the exhaust hoses extensions. 

o

 

NEVER  run  the  pump  in a  radius  of 3  ft (1m) of a building  or  combustible 

object. 

o

 

NEVER operate the engine if there is an accumulation of grass, leaves, or 

other combustible material around, behind or under the muffler.  

o

 

NEVER run the engine without a muffler or proper exhaust system.  

o

 

NEVER operate the engine if the fuel tank cap is removed, do not fill the tank 

while the engine is running.  If fuel is spilled, move machine away from the 

area  of  the  spill  and  avoid  creating  any  source  of  ignition  until  it  has 

completely evaporated.  

o

 

NEVER run the engine in an explosive environment. 

o

 

NEVER touch the spark plug or its components while running the engine; it 

could give you an electric shock.  

o

 

NEVER put your foot or hand near moving parts. 

o

 

NEVER wear loose, bulky or torn clothing while operating the pump, it could 

catch on moving parts and lead to serious injury. 

o

 

NEVER  let  your  pump  run  unattended.  It  must  always  be  operated  by 

trained personnel assuring the stability and direction of discharge hose. 

o

 

NEVER operate this machine while under the influence of drugs or alcohol. 

o

 

NEVER spray the pressurised flow of water at a person or animal. 

DANGER 

 

Содержание PFP-18HPVGD-MR-CE
























Отзывы: