Ceragon FibeAir IP-10C Скачать руководство пользователя страница 58

Страница: 58 / 63

FibeAir® IP-10C

Installation Guide

Ceragon Proprietary and Confidential

Page 58 of 63

4.2

Remote Mount Installation with an Imperial Waveguide
– 13-15 GHz

1 Mount the RFU-C Adaptor supplied with the RFU-C Remote Pole Mount kit

using the four flat screws supplied with the RFU-C Adaptor kit.

2 Mount the adapting bar using two M8 flat screws.
3 Mount the IP-10C unit on the Remote Pole Mount kit, and tighten it using

the four M8 captive screws and washers supplied, with the IP-10C. Thread
the screws without fastening. After all four screws are threaded in the
correct location, tighten the screws starting from the bottom screws.

4 Connect the Flexible Waveguide and sealing O-Ring supplied with the

Flexible Waveguide Imperial kit to the RFU-C Adaptor. Tighten the four
screws supplied with the Flexible Waveguide Imperial kit.

Содержание FibeAir IP-10C































































Результаты поиска

Содержание FibeAir IP-10C

Отзывы:

Похожие инструкции для FibeAir IP-10C

Бренды по названию

Популярные бренды

Ceragon FibeAir IP-10C, Руководство по установке

Результаты поиска

Содержание FibeAir IP-10C

Отзывы:

Похожие инструкции для FibeAir IP-10C

Бренды по названию

Популярные бренды