Ceragon FibeAir IP-10C Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 63

Ceragon FibeAir IP-10C Скачать руководство пользователя страница 42

FibeAir® IP-10C

Installation Guide

Ceragon Proprietary and Confidential

Page 42 of 63

3.4

1+1 HSB Remote Mount Installation

The following components are necessary for a 1+1 HSB remote mount
installation:

Item

Description

Quantity Remarks

I

IP-10C RADIO

2

2

RFU-C COUPLER KIT

1

3

RFU-C REMOTE MOUNT ADAPTOR KIT

1

For 6-13 GHz

In 1+1 remote mount configuration, the IP-10C is attached to a coupler.

Important!

Do not remove the transparent pressure window located on
the coupler ports!

To install an IP-10C in a 1+1 HSB remote mount configuration:

1 For 6-13 GHz installations only, mount the RFU-C remote adaptor and

O-Ring to the pole mount using the four flat M5 screws supplied in the
RFU-C Remote Mount Adaptor kit, and tighten the screws.

2 Mount the IP-10C coupler to the RFU-C pole mount bracket using the four

M8 screws and washers supplied with the RFU-C Coupler kit, and tighten
the screws.

«
...
40
41
42
43
44
...
»

Содержание FibeAir IP-10C
































































Отзывы:

Нет отзывов