Ceragon FibeAir IP-10C Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 63

background image

FibeAir® IP-10C

Installation Guide

Ceragon Proprietary and Confidential

Page 33 of 63

2.13

Grounding the IP-10C

1 On the front side of each IP-10C, loosen the nut, plain washer, and serrated

washer.

2 Place the cable lug (supplied with the IP-10C housing kit) on the screw.
3 Secure the cable lug.

IP-10C Grounding Cable



The unit’s earthing screw terminal shall be permanently connected to
protective earth in a building installation in accordance with applicable
national code and regulations by a service person.



A 2-Pole circuit breaker, a branch circuit protector, suitably certified in
accordance with applicable national code and regulations, rated maximum
20A, shall be installed for full power disconnection in a building
installation.



Any outdoor antenna cable shield shall be permanently connected to
protective earth in a building installation.

When selecting a power source, the following must be considered:



DC power can be from -40 VDC to -60 VDC.



Recommended:

Availability of a UPS (Uninterrupted Power Source),

battery backup, and emergency power generator.



Whether or not the power source provides constant power (i.e., power is
secured on weekends or is shut off frequently and consistently).



The power supply must have grounding points on the AC and DC sides.

Caution!

The user power supply GND must be connected to the positive pole in the IP-10C
power supply. Any other connection may cause damage to the system!

Important:

For the warranty to be honored, you must install the IP-10C
in accordance with the instructions above.

!!

«
...
31
32
33
34
35
...
»

Содержание FibeAir IP-10C
































































Отзывы:

Нет отзывов

Похожие инструкции для FibeAir IP-10C

Бренд: Harman Kardon Страницы: 20

Бренд: Harman Kardon Страницы: 20

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 146

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 64

Бренд: Harman Kardon Страницы: 4

Бренд: Harman Kardon Страницы: 187

Бренд: Harman Kardon Страницы: 187

Бренд: Harman Kardon Страницы: 10

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 48

The Counterpoint A-400

Бренд: Harman Kardon Страницы: 5

Бренд: Harman Kardon Страницы: 24

Бренд: Harman Kardon Страницы: 11

Бренд: Harman Kardon Страницы: 8

Бренд: Harman Kardon Страницы: 9

Бренд: Harman Kardon Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды