Ceragon FibeAir IP-10C Скачать руководство пользователя страница 17

Страница: 17 / 63

FibeAir® IP-10C

Installation Guide

Ceragon Proprietary and Confidential

Page 17 of 63

For vertical polarization, locate the holes above and below the letter
“V” on the pins and fasten the two screws.

Note:

For 6 GHz, separate irises are used for vertical and
horizontal polarization. The vertical iris comes assembled
with the IP-10C. The horizontal iris (MA-1840-X,
IP-10C Twist 6Ghz Horizontal) is included in the IP-10C
package.

2.9

Connecting Flexible Waveguides to the IP-10C

For an IP-10C operating in bands of 6-13 GHz, a remote mount adaptor must
be used to connect a flexible waveguide.

For an IP-10C operating in bands of 15-42 GHz, you must remove the iris
before connecting a flexible waveguide to the antenna port.

The following table provides the marketing models for the remote mount
waveguide adaptor kits required, per frequency.

Freq (WG standard) 6HGz (UBR70)

7-8GHz (UBR84)

10-11GHz (UBR100)

13GHz (UBR120)

Remote Mount WG
adaptor kit

RFU-C6-RM_ADAPT RFU-C7_8-RM_ADAPT RFU-C10_11-RM_ADAPT RFU-C13-RM_ADAPT

Remote Mount Kit

RFU-C-PoleMount

Содержание FibeAir IP-10C































































Результаты поиска

Содержание FibeAir IP-10C

Отзывы:

Похожие инструкции для FibeAir IP-10C

Бренды по названию

Популярные бренды

Ceragon FibeAir IP-10C, Руководство по установке

Результаты поиска

Содержание FibeAir IP-10C

Отзывы:

Похожие инструкции для FibeAir IP-10C

Бренды по названию

Популярные бренды