Century Helicopter Products Predator 60/70 SE Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 20

background image

Attach the clutch shoe with the M3 button socket bolts using
threadlock.

Clutch
Shoe

Fan
Assembly

Clean the clutchbell and inside of the bearing with alcohol.
Apply a small amount of permanent locktight around the top
15mm edge of the aluminum clutchbell where it will contact the
bearing. Ensure the bearing is against the clutchbell. Press evenly
and firmly as this is a very tight fit. A press should be used.

#HW6045
Lower Short
Bearing Block

#HW6013

Clutch Bell Assembly 10T

#HW6013A

Clutch Bell Assembly 11T

#HW6013B

Clutch Bell Assembly 12T

#HW6014

Replacement Clutch Lining

#HW6007
Clutch Shaft
Bearing Block

#HW6045

Lower

Long

Bearing

Block

M3x12 Socket Screw x 2

Clean the top of the clutchbell gear and inside of the upper
bearing with alcohol. Apply a small amount of permanent
locktight around the top edge of the clutch gear where it will
contact the bearing. Press the clutch shaft bearing block in
place. Attach the long bearing block with M3x12 socket
screws but do not tighten at this time.

#HW6042
Main Shaft Bearing Block

M3x8 Socket Screws x 8

26mm
Threaded Hex
Spacer

Attach the clutchbell and bearing block assembly (flange
down), main shaft bearing block and front hex threaded spacer
with M3x8 socket screws to the left upper side frame. Do not
use locktight at this time. Notice the countersunk hole below
the bearing is on the outside.

#HW6110

Upper left Side

Frame

Prepare the rear ccpm servo, attach the rubber servo tabs and
the eyelets from the top of the servo.

#HI3205
Servo
Mount
Tabs

Rubber servo tabs,

eyelets and screws

provided with radio.

Install the rear ccpm servo into the inside of the right side of
the upper side frames. Be careful, look for the countersunk
hole below the bearing is on the outside.

Servo
output
shaft to
rear of
helicopter.

19

20

22

6

21

23

24

Pre-Assembled

Flange on

bearing block

faces down.

«
...
4
5
6
7
8
...
»

Содержание Predator 60/70 SE





















Отзывы:

Нет отзывов

Похожие инструкции для Predator 60/70 SE

Бренд: Faller Страницы: 4

Бренд: marklin Страницы: 36

Бренд: ubisoft Страницы: 21

Big Boy Locomotive

Бренд: REVELL Страницы: 11

Бренд: LGB Страницы: 3

Бренд: E-FLITE Страницы: 32

Бренд: MegaTech Страницы: 12

Zoom Avia B.534 IV. Series Weekend

Бренд: Eduard Страницы: 2

Бренд: Trix Страницы: 20

HANGAR 9 Fun Scale PT-19 PNP

Бренд: Horizon Hobby Страницы: 48

Lockheed-Martin F-117A Nighthawk

Бренд: REVELL Страницы: 10

Loving Family Sweet Melodies Bedroom 75107

Бренд: Fisher-Price Страницы: 2

Бренд: LGB Страницы: 12

Solo Pro 100D 3D

Бренд: Nine Eagles Страницы: 18

Thomas & Friends Thomas to the Rescue

Бренд: Mega Bloks Страницы: 2

Baby GymTasTics Zebra K0317

Бренд: Fisher-Price Страницы: 6

Newborn Necessities Gift Set

Бренд: VTech Страницы: 10

Бренд: PICO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды