Central Pneumatic Contractor 97520, Руководство по установке и эксплуатации, Страница: 17 / 24

SKU 98464 For technical questions, please call 1-800-444-3353. Page 17
Troubleshooting guide
Stop using the Nailer/Stapler immediately if any of the following problems occur.
Repairs and part replacements must be done only by a qualified technician.
All procedures in bold on this chart are to be attempted only be a qualified techn ician.
Problem Likely Cause Solution
Air leaking at Trigger
area.
O-Rings in Valve Body are damaged. Replace O-Rings and check
contact trip operation.
Air leaking between
Housing and Nose.
Loose screws in Housing. 1.
Damaged O-Rings/Bumper. 2.
Tighten screws. 1.
Replace O-Rings or Bumper. 2.
Air leaking between
Housing and Cap.
Loose screws. 1.
Damaged Gasket. 2.
Tighten Screws. 1.
Replace gasket. 2.
Runs slowly or has
power loss.
Insufficient oil. 1.
Broken Spring in Cylinder Cap. 2.
Exhaust is blocked. 3.
Lubricate as instructed. 1.
Replace Compression Spring.
2.
Clean Cap or replace damaged 3.
parts.
Tool skips a nail.
Worn Bumper or damaged Pusher 1.
Spring.
Dirt in Driver Guide.
2.
Inadequate airflow to Nailer/ 3.
Stapler.
Worn or dry O-Ring on Piston.
4.
Damaged O-Ring on Trigger Valve. 5.
Cap Gasket leaking. 6.
Replace Bumper or Pusher 1.
Spring.
Clean channels in Driver Guide. 2.
Check hose and compressor 3.
fittings.
Replace or lubricate O-Rings. 4.
Replace O-Rings. 5.
Replace gasket.
6.
Fasteners are
jammed.
Guide on driver is worn. 1.
Fasteners are wrong size or 2.
damaged.
Magazine or Nose screws are loose.
3.
Driver is damaged. 4.
Replace guide. 1.
Use correct, undamaged 2.
Fasteners.
Tighten screws.
3.
Replace driver. 4.
Nailer/Stapler will not
drive down tight.
Rounded Driver slipping off 1.
fastener crown.
Lack of air pressure.
2.
Slow cycling and loss of power. 3.
Replace driver. 1.
Supply correct pressure. 2.
Check Compression Spring for 3.
broken coils or reduced length.
make sure Exhaust is clear.
Blade driving fastener
too deeply.
Worn Bumper (94) and/or Piston
Spacer.
Replace either or both parts.
All procedures in bold on this chart are to be attempted only be a qualified technician.
PLEASE REAd THE FOLLOWINg CAREFuLLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN
THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL
RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.