manualshive.com logo in svg

CEM Discover Bio, Инструкция по установке и эксплуатации, Страница: 18 / 20

Поделиться
Скачать
CEM Discover Bio Скачать руководство пользователя страница 18

Discover Bio

™

 Manual Microwave Peptide Synthesizer

600423 • Revision 2 • August 2017

18

Spare Parts and Accessories

System

Accessories and Consumables

Product

Part Number

Discover Bio System

925496

Includes the following:

Discover Bio Microwave Reactor (select one)

120 v (60 Hz) Power Supply

909450

240 v (50 Hz) Power Supply

909455

Power Cord

(varies by country)

Discover Bio Wash Station (select one)

120 v (60 Hz) Power Supply

908400

240 v (50 Hz) Power Supply

908405

Power Cord

(varies by country)

Fiber-Optic Temperature Control

541176

Discover Bio Accessory Kit

908410

Product

Part Number

4 mL Reaction Vessel Assembly

543505

Replacement Frits for 4 mL Vessel (Qty 50)

215005

25 mL Reaction Vessel Assembly

543500

Replacement Frits for 25 mL Vessel (Qty 50)

215055

50 mL Polypropylene Centrifuge Tubes (Qty 25)

167150-M

1 L Glass Bottle

167550

Two-Port GL45 Bottle Cap with Dip Tube

167559

Tubing for Bottle Cap

216780-M

Dip Tube Filters (Qty 50)

167485-M

Bottle Holder

543510

Fiber-Optic Temperature Probe

314325

Replacement Thermowell

181110

Содержание Discover Bio





















Отзывы:

Нет отзывов