manualshive.com logo in svg

CE+T Power TSI VEDA, Руководство пользователя

Поделиться
Скачать
CE+T Power TSI VEDA Скачать руководство пользователя страница 10

5. Accessories

5.1  Cabinet

Powder coated (RAL 7035), 19 “welded steel sheet cabinet with 600x600mm foot print. Cabinet designed for top cabling or 
bottom cabling. 

„

„

1100mm (600x600mm) 

21U

„

„

1800mm (600x600mm) 

37U

„

„

2110mm (600x600mm) 

44U

The cabinet comes with a separable top cover to facilitate cabling. Tie strap support at cable entrance/exit.

Door optional accessory

Veda is suitable for easy integration in 300, 400, 600 mm depth cabinet.

5.2  AC distribution unit

5.2.1  Distribution Rack

  

The standard AC output distribution is designed with a 
8X 6A breaker with Lamp indication and Voltage test 
point

Max current per AC DU is 20A, max current per output connector is 6A ,applicable only upto 4.5KVA  A la Carte system/pack.

Alarm for AC output breakers is present (OF or SD). The alarm function is common and use one of the digital input on the control 
unit. 

10 

– TSI VEDA – User manual – v7.1

Содержание TSI VEDA










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды