manualshive.com logo in svg

CE+T Power Bravo 10 - 48/230, Руководство пользователя

Поделиться
Скачать
CE+T Power Bravo 10 - 48/230 Скачать руководство пользователя страница 27

8.3.1  LED indications

Three LED’s are present behind the front black plastic of the controller to indicate major alarm, minor alarm, and system 
status. These LED’s are not visible until they illuminate during the corresponding action occurs.

(Red) Major alarm

(Orange) Minor alarm

(Green) System status

Front black plastic

8.3.2  Menu structure

The home page is the default page in the LCD interface, and other pages are arranged in the below sequence.

Inview S Slot 

LCD Interface

Events

Info

Home

Action

DC

AC Out

System

AC In

Logs

8.4  Inview S and Inview S Slot - Web Interface

The web interface of both controller Inview S and Inview S Slot is same, and the user can access the controller on the 
laptop through ETH port. 

This section provides an overview of the web interface, refer Inview S user manual for detailed information.

 Interface

27 

- Bravo 10 - 48/230 - User manual - v1.2

Содержание Bravo 10 - 48/230












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды