CD Automation REVO REVEX3PH Скачать руководство пользователя

Страница: 11 / 58

REVEX

3PH from 120A to 210A

User’s manual

Software Configurator

Thyristor configurator software is free and is

possible download it from our site.
If the Order Code is in line with requirement,

then unit has been already configured in

Factory and it’s ready to use.
You need the software only to modify the

ordered configuration. Anyway we suggest

to check the unit on the machine with the
“Test unit” section.
For install the software, launch the program
and follow the instructions on the screen.

Run the software configurator and set the

correct serial port number by menu setting-
serial com – port number.

To connect the unit at the PC, it’s necessary
to use the micro USB 2.0 Modbus RTU cable.
USB connection need a driver to work

properly, you can find it from our site.

However the configuration software installer

will install as default the correct driver.

with display

Option code:

0/4/5/6

on digit 12

without display

Option code:

1/2/3/7

on digit 12

Micro USB

Software Configurator download link:

https://www.cdautomation.com/download/cd-automation/software/ThyristorConfigurator_ver6.exe

Содержание REVO REVEX3PH



























































Результаты поиска

Содержание REVO REVEX3PH

Отзывы:

Похожие инструкции для REVO REVEX3PH

Бренды по названию

Популярные бренды

CD Automation REVO REVEX3PH, Руководство пользователя

Результаты поиска

Содержание REVO REVEX3PH

Отзывы:

Похожие инструкции для REVO REVEX3PH

Бренды по названию

Популярные бренды