1
2
3
1
2
1
1
1
B
A wall mount bracket is included and can be installed if needed. Tightly
coil the telephone cord around the four guides on the inside of the wall
mounting bracket. Pull the telephone cord through the center opening on
the wall mounting bracket. Refer to the drawing. The handset can be
charged face out or face down, even when wall mounted.
INITIAL SETUP
WALL/DESK USE
This switch tells the CP-2070 to dial out with either touchtone or pulse signals to match the service you
have with your local telephone company. The CP-2070 is shipped with the
TONE/PULSE SWITCH
in the TONE position. If you do not have touchtone service, set the switch to pulse on the back of the
charging cradle.
TONE/PULSE SWITCH
PULSE TONE
The CP-2070 is shipped with the handset RINGER ON/OFF SWITCH in the ON position and the base
RINGER OFF/LOW/HIGH SWITCH in the HIGH position. You can independently set the ringers of the
CP-2070.
RINGER ON/OFF
C
NOTE:
■
If the handset is in “Standby Mode” but not in the
charging cradle, the display will go blank after a short
time to conserve battery power.
HANDSET / TELEPHONE OPERATION
STANDBY MODE
The CP-2070 is in “Standby” mode
whenever it is idle, waiting for a call. If the
handset is in the charging cradle, the
display will either be blank
OR
If you have new caller ID entries from
recent unanswered calls, it will show the
“NEW CALLERS” message with the
number of new callers at the lower far
right of the display screen. Press
CALLER ID
to view the names and
numbers of “New Callers”.
1
2
Pick up the handset and press
TALK
. The
following display will be briefly shown. This
display indicates that the handset is estab-
lishing contact with the charging cradle.
TO PLACE A CALL
A dial tone will be established. (In this
example, CH03 is the current channel
number of 60 available channels in your
area.) Wait for dial tone and dial the phone
number. The number will appear in the
display as you dial.
NOTE:
■
The HANDSET LINE IN-USE INDICATOR on the
charging cradle lights solid to show the handset is in
use.
1
To hang up, press
TALK
or return the
handset to the charging cradle.
TO END A CALL
NOTE:
■
When you return the handset to the charging cradle,
you are hanging up the phone and returning to
Standby Mode. The CP-2070 is now ready to receive
a call and the
CHARGING INDICATOR lights solid to
show that the battery is charging.
1
Press
TALK
twice (“off” and “on.”) Wait
for dial tone and dial the correct number.
IF YOU MISDIALED
A NUMBER
1
2
1
TO RECEIVE A CALL
When the phone rings, pick up the cordless
handset and press
TALK
. You will briefly
see the “SCANNING CHANNELS” display,
followed by the “VOLUME” display. Speak
to the caller.
To hang up, press
TALK
on the handset or
return the handset to the charging cradle.
HANDSET VOLUME CONTROL
Whenever the CP-2070 is in “Talk” mode, the
handset volume will be displayed.
Press the
DOWN
or
UP ARROW KEY
to adjust the volume during a call. The
volume will remain at that level for your
next call.
About 10 seconds after you enter “Talk” mode, a
Call Timer will appear on the display. The timer
will automatically be reset whenever you place a
new call.
NOTES:
■
The length of time shown on the display is intended
only to be an estimate duration of a phone call.
CASIO makes no guarantees regarding the accuracy
of this timer.
■
The Call Timer will not be disrupted if
HOLD is
pressed. The Hold timer (5 minute count down timer)
will display and the Call Timer will continue, hidden
from view, during any Hold mode.
CALL TIMER
1
Press the
RIGHT ARROW (CHANNEL)
KEY
to view the approximate length of the
last call after you have hung up the phone.
LAST CALL TIME DISPLAY
After
TALK
is pressed, the CP-2070 selects
the best of 60 available channels in your
area. If you hear noise or interference while
using the CP-2070, press
CHANNEL
on
the handset to change channels.
CHANGING CHANNELS
MANUALLY
1
If you subscribe to a call waiting service
and you receive another call while using the
phone, press
FLASH
to answer the
second call. To return to the first call, press
FLASH
again.
FLASH/CALL WAITING
FLASH
may also be used on a business phone
system (CENTREX, PBX) for transferring calls.
1
2
Press
HOLD
to place a call on hold. The
LINE IN-USE INDICATOR will flash slowly.
You may place a call on hold while using the
cordless handset.
HOLD
NOTE:
■
You can place a call on hold for up to 5 minutes.
During
HOLD, do not return the handset to the
charging cradle. Doing so will disconnect the caller.
To continue your phone conversation,
press
TALK
,
HOLD
, or pick up an
extension phone connected to the same
line. When the extension phone is picked
up, the CP-2070 automatically disconnects
itself from the line. Extension phone pick-
up during HS Hold mode will discontinue
the Hold mode, connect the call to the new
extension phone, and cause the CP-2070 to
go idle after a 10 -second display time out.
NOTE:
■
The Call Timer will not be disrupted if
HOLD is
pressed. The Hold timer (5 minute count down timer)
will display and the Call Timer will continue, hidden
from view, during any Hold mode.
1
2
Send-Key Dialing is extremely reliable because
you can see the number you have entered before
actually dialing it.
DIALING A NUMBER USING
THE SEND KEY
(DISPLAY & DIAL)
Make sure the CP-2070 is in “Standby
Mode”. Without pressing the
TALK
button,
enter the number you wish to dial. If you
make a mistake, use
DELETE
to make
changes. The last digit entered will be
deleted. Each time
DELETE
is pressed, the
previously entered digit will be erased.
After you have correctly entered the entire
number you wish to dial, press
SEND
. The
CP-2070 will dial the number.
1
The CP-2070 remembers the last number you
dialed. The redial memory will hold up to 32
digits. Every time you dial a new telephone
number, the redial memory is updated with that
new number.
REDIAL
Press
TALK
and wait for a dial tone.
2
Press
REDIAL
.
1
If you receive a busy signal after placing a call
and you wish to try again immediately, there is no
need to hang up the phone.
REDIAL WHEN BUSY
Press
REDIAL
while hearing a busy signal
and the CP-2070 will automatically hang
up, reconnect, and dial the number again.
1
Display Redialing allows you to view the contents
of the redial memory before dialing. This is
useful if you aren’t sure what number was last
dialed on the CP-2070.
DISPLAY REDIALING
Make sure the unit is in “Standby” mode.
Press
REDIAL
. You will be able to view
the last 15 digits of the last number dialed.
2
Press
SEND
to dial.
1
The CP-2070 cordless handset operates like any
other cordless handset. You can use it in the
yard, at the pool, at the mailbox, or any place
within the operating range of the charging cradle.
If you move out of the charging cradle’s operating
range, you may hear a triple beep warning tone
and/or static interference. Move closer to the
charging cradle to deactivate the alarm and
prevent disconnection. If you remain out of range
for too long, the CP-2070 will disconnect from
the line.
If the handset loses its security code, you will
also hear an alarm tone. To reset this security
code, place the handset in the charging cradle for
a few seconds. Pick up the handset and try your
call again.
Interference from other appliances may also
cause the alarm to sound. To prevent
interference, move the charging cradle to
another location and raise its antenna.
Press
PAGE
on the charging cradle. The
base unit will issue beeps to confirm that
the paging signal to the HS has been
enabled. You will hear the handset ring.
PAGING THE HANDSET FROM
THE CHARGING CRADLE
2
To cancel the page, either press
PAGE
again or
TALK
twice on the handset or
place the handset in the charging cradle.
NOTE:
■
After seven rings the page will stop.
1
You can check the power level of the battery to
avoid battery depletion.
BATTERY CONDITION
Press
BATTERY
when the handset is out
of the charging cradle. The following
display will appear when the battery is fully
charged:
As the battery discharges, the stack symbols will
disappear, starting from the right. When the
battery is low, the display will look like:
2
Press
BATTERY
again or wait a few
seconds to leave battery condition mode.
NOTES:
■
Charge the battery for 12-15 hours before using.
■
If
BATTERY is pressed while the handset is in the
cradle, "CHARGING" will appear in the LCD.
LOW BATTERY INDICATOR
The CP-2070 will automatically detect a low
battery. If this happens, you will hear a double
beep, and the “LOW BATTERY” display will
appear.
If the Low Battery indicator appears while you are
talking on the CP-2070, you may only have a few
minutes left before the battery discharges
completely, in which case you will be
disconnected. To prevent this, simply pick up an
extension phone and place the CP-2070 back in
the charger. Place the handset in the charger for
12 - 15 hours to recharge the battery.
NOTE:
■
The battery can be recharged many times, but if you
get a low battery indication even after 12-15 hours of
charging, you should replace the battery pack. See
the Accessories order form to purchase a battery
pack.
OUT OF RANGE ALARM
3
1
If you choose to take the second call, press
FLASH
to answer it.
You must subscribe to a Caller ID service
(available from most local telephone companies)
in order to receive Caller ID information. Most
Caller ID services offer the following two options:
1.Standard Caller ID with name and number
The name, phone number and local time (if
available) of the incoming call are received
after your phone rings.
2.Call Waiting Caller ID with name and number
The name, phone number and local time (if
available) of the incoming call are received
after your phone rings. If you are on the phone
and receive another call, you will hear a tone,
telling you there is a call waiting. The Call
Waiting Caller ID information will appear on the
display.
CALLER ID SERVICE OPTIONS
When you receive a call, the CP-2070 will receive
the Caller ID information from your phone
company within the first two rings. Caller ID
information will display even if the ringer is set to
off.
When all of the data is received, you will hear a
low-high confirmation tone and the Caller ID
information will appear on the display:
ANSWERING
CALLER ID CALLS
Once you hear the confirmation tone, you
can press
TALK
to answer the call and
automatically retain all the Caller ID
information received.
NOTE:
■
If you press TALK before you hear the Caller ID
confirmation tone, the Caller ID information for that
call will be lost.
ANSWERING CALL WAITING
CALLER ID CALLS
If you subscribe to a Call Waiting Caller ID service
with your telephone company and you program
Call Waiting Caller ID to "ON," the CP-2070 can
receive a Caller ID call while you are on the line
with another party.
If a second call comes while you are on the
phone, your CP-2070 will beep.
You can now view the LCD screen to see the
name and number of the incoming caller.
You can decide whether to answer the
second call or ignore it and continue with
the first call.
4
You may continue to press
FLASH
to
switch between the two calling parties
indefinitely.
The CP-2070 automatically saves up to 50 Caller
ID entries. Any Caller ID information (name,
phone number, date, time) that is transmitted will
be stored for your reference or use in the
autodialer and redial memory.
All Caller ID names and numbers are stored in
reverse order of receipt (last call is displayed as
highest memory number.) If the memory
becomes full, the newest entries will be saved
and the oldest ones will be erased.
SAVING CALLER ID
INFORMATION
Even if Caller ID calls are not answered, the
CP-2070 will automatically store the Caller ID
information into memory.
If the handset is in the charger, “NEW CALLERS”
will appear on the display. This message will stay
on the screen and go away after you review the
stored Caller ID information.
The NEW CALLS count in the LCD indicates all
CPID records not yet viewed. The NEW CALLS
INDICATOR on the base will light until you have
pressed the Caller ID button to review stored
Caller ID records.
NOTE:
■
If the handset is out of the cradle, the LCD screen will
only say <NEW CALLERS> for 5 seconds and then
go blank. It will say <NEW CALLERS> again if put
back into the charging cradle.
RECEIVING CALLER ID
INFORMATION IF CALL
IS NOT ANSWERED
If you received calls while you were away from
your CP-2070, you can retrieve the stored Caller
ID entries from memory. CPID records can also
be viewed and scrolled while off-hook (while you
are on an active call).
2
1
1
REVIEWING STORED
CALLER ID INFORMATION
Press
CALLER ID
. The entry for the
most recently received call will be
displayed.
The name will be displayed on the top line, the
number on the second line, and the time and date
of that call will be displayed on the third line of the
display (all information is displayed at once). The
word NEW indicates that this is a new caller ID
record. The word NEW will be displayed for each
record that is being viewed for the first time. The
two digit number (example "22") in the lower right
corner of the display indicates that N Johnson is
your most recent caller and it is your twenty-
second call. This helps you keep track of how
many entries are currently stored in your CP-2070.
2
Use the
DOWN
or
UP ARROW KEY
to
see the other entries.
DOWN
scrolls
through older records and
UP
scrolls the
opposite direction.
“BLOCKED” AND
“UNAVAILABLE” MESSAGES
The CP-2070 allows you to place calls using
stored Caller ID information.
Press
CALLER ID.
(You may press
TALK
first if you wish. Caller ID can be dialed
from off hook mode or on hook mode).
Locate the desired numbers by scrolling
through saved Caller ID information using
the
DOWN
or
UP ARROW KEY
.
(Holding down the DOWN or UP ARROW
KEYS will automatically fast scroll through
Caller ID records).
3
Press
SEND.
4
If your area code is set to 000 in the
CP-2070 the LCD will display the first of the
three different dialing options. Press the
UP
or
DOWN ARROW KEY
to view the
rest of the dialing option.
NOTES:
■
If you have programmed your local area code into
the CP-2070 before using this feature then the
CP-2070 will not prompt you for different dialing
options. See “Programming the CP-2070” for more
information.
■
If no button is pressed for 30 seconds during
viewing of Caller ID information the LCD will time-out
to a blank display.
Specific Caller ID entries may be deleted.
DELETING INDIVIDUAL
CALLER ID ENTRIES
1
2
3
Press
CALLER ID
.
Press the
DOWN
or
UP ARROW KEY
to locate the entry you wish to delete.
Press and release
DELETE
. You will hear
a double beep and the “Delete ?” message
will appear.
4
Press
DELETE
again within 5 seconds to
confirm. The entry will then be deleted.
1
2
Press
CALLER ID
.
DELETING ALL CALLER ID
INFORMATION
Press and hold
DELETE
until you see the
“Delete All ?” message appear on the
display.
3
Press
DELETE
again within 5 seconds to
confirm. All Caller ID entries will then be
deleted.
If you do not subscribe to a Caller ID service, you
can still benefit from most of the CP-2070’s
advanced features. However, you should be
aware of the following:
1. Pressing
CALLER ID
will simply display the
“NO CALLS” message
2. The Call Waiting Caller ID and Outside Line
program options will have no effect.
NOTE:
■
Certain sounds and voice pitches may occasionally
cause the CP-2070 to incorrectly “think” that the
local phone company is sending Call Waiting Caller
ID information. Although no Caller ID data will show
up on the display, the CP-2070 may mute the phone
line for a second or so. To prevent this annoyance,
simply make sure that the Call Waiting Caller ID
program option is set to “OFF”.
USING THE CORDLESS PHONE
WITHOUT CALLER ID
SCANNING
CHANNELS...
VOLUME
CH03
BATTERY
BATTERY
SMITH JAN
1 310 555 1234
1/22 09:01
AM
10
NEW
DIALING STORED CALLER ID
NUMBERS
1
1
1
You may store up to 20 of your most frequently
dialed names and numbers into the autodial
memory. Autodial names can be up to 16
characters long, and the accompanying phone
numbers can be up to 24 digits each.
STORING NAMES AND
NUMBERS IN AUTODIAL
Press
PROGRAM
.
2
Press
AUTODIAL
.
3
Press the
LEFT
or
RIGHT ARROW
KEY
to locate a memory location.
4
Enter a telephone number on the keypad.
5
Press the
UP ARROW KEY
to move
the cursor to the name field.
6
Enter the name using the keypad.
Pressing a key once displays the first
upper case letter on that key. Pressing it
repeatedly will cycle through all of the
upper and lower case characters on that
key. Stop when the desired character
appears in the display. The "1" key
provides unique characters and icons.
7
Press the
RIGHT ARROW KEY
to
move the cursor one space to the right.
8
Press
AUTODIAL
again when you finish
to save the new entry. Nothing will be
stored until the AUTODIAL key is pressed.
9
Press
PROGRAM
to exit the mode.
1
When you are programming numbers into the
autodialer, the
HOLD (PAUSE)
key can be used to
insert a two-second “pause” (wait period)
between digits.
For example, if you need to dial a “9” in order to
obtain an outside line, you can use the
PAUSE
key to insert a two second pause for the second
dial tone.
PROGRAMMING PAUSES IN
AUTODIAL
Just press “
9
“,
PAUSE/HOLD
, and
then the number you wish to program.
1
Press
AUTODIAL.
(You may press
TALK
first if you wish. Autodial can be
dialed from off hook mode or on hook
mode). If phone numbers are programmed
into the autodial memory, the first
programmed number will appear in the
display.
USING AUTODIAL
2
Press the
DOWN
or
UP ARROW KEY
to select an autodial number.
3
When you locate the number, press
SEND
to dial it. The CP-2070 will
automatically dial the number on the
display.
NOTE:
■
If no button is pressed for 30 seconds during
viewing of autodial records the LCD will time-out to a
blank display.
Press
PROGRAM
.
A FASTER WAY TO USE THE
AUTODIALER
If you know the autodial number (01 - 20) of the
name and number that you wish to call, you can
enter it directly.
For example, if you know that the name
and number of the person you are calling
are stored in autodial 06 just press
AUTODIAL
, “
6
“,
SEND
. The CP-2070
will then establish a dial tone and dial the
number.
EDITING AUTODIAL ENTRIES
2
Press the
UP ARROW KEY
two times or
the
DOWN ARROW KEY
five times (or
just press
AUTODIAL
).
3
Press the
LEFT
or
RIGHT ARROW
KEY
to locate the number you wish to
edit.
4
Press the
UP ARROW KEY
. The entire
phone number will flash. When the entire
phone number is flashing, entering a
number on the keypad will erase the
previously stored phone number from the
display and replace it.
5
If you only wish to change a few digits,
press the
LEFT ARROW KEY
to activate
the cursor, and then use the
RIGHT
or
LEFT ARROW
,
DELETE
, and
NUMBER
keys to make changes.
6
Press the
UP ARROW KEY
. The entire
name will now flash. As in the previous step,
entering a number key (for a character
entry) at this point will erase the flashing
name from the display and replace it.
7
If you only wish to change a few letters,
press the
RIGHT ARROW KEY
to
activate the cursor, and then use the
RIGHT
or
LEFT ARROW
,
DELETE
, and
NUMBER
keys to make changes.
8
Press
AUTODIAL
once the correct
information is entered and your changes
will be saved.
9
Press
PROGRAM
to exit the
programming mode.
1
To erase numbers in autodial, press
AUTODIAL
.
ERASING AUTODIAL NAMES
AND NUMBERS
2
Press the
DOWN
or
UP ARROW KEY
to find the autodial name and number you
wish to erase.
3
Press and release
DELETE.
"DELETE ?"
will appear in the display.
4
Press
DELETE
again within 5 seconds to
confirm. The entry will then be deleted.
1
2
3
ERASING ALL AUTODIAL
NAMES AND NUMBERS
If you wish to delete all Autodial names
and numbers, press
AUTODIAL
.
Press and hold
DELETE
until "DELETE
ALL?" appears in the display.
Press
DELETE
again within 5 seconds to
confirm. All autodialer entries will then be
deleted.
1
2
3
4
This feature allows you to transfer a phone
number from Caller ID memory directly into the
Autodial Memory. This saves you time and
eliminates the chance of entering an incorrect
phone number into memory. You can even edit
the name and number before you complete the
transfer.
TRANSFER CALLER ID TO
AUTODIAL MEMORY
Press
PROGRAM
. The “PROGRAM
MODE” display will flash on the screen.
Press
AUTODIAL
. You will see 01
flashing in the lower right-hand corner of
the display. (The rest of the display may
or may not be blank, depending on the
current contents of location #1).
NOTE:
■
If you make a mistake or change your mind at any
time during this procedure, simply press
PROGRAM
again to quit.
Use the
LEFT
or
RIGHT ARROW KEY
to select the autodial location where you
wish to transfer the Caller ID number.
(Again, the rest of the display may or may
not be blank. If it is not blank, the
contents of this location will be written
over once you complete the transfer.)
Press
CALLER ID
. The most recently
received Caller ID entry will appear in the
display.
5
6
7
Use the
DOWN
or
UP ARROW KEY
to
select the Caller ID entry you wish to save.
You can either save the entry exactly as it
appears, or you can edit the name and/or
number. To save the entry without any
editing, just press
AUTODIAL
. To edit
the entry, press the
UP ARROW KEY
and proceed as described in the "TO EDIT
AUTODIAL ENTRIES" section.
When you are finished, press
PROGRAM
to exit “Program” mode.
TRANSFER REDIAL NUMBER
TO AUTODIAL MEMORY
This feature allows you to transfer a phone
number from the Redial Memory directly into the
Autodial Memory. If you wish, you can add a
name before you complete the transfer.
Follow steps 1-3 under "TRANSFER
CALLER ID TO AUTODIAL MEMORY".
Press
REDIAL
. The contents of the
Redial Memory will appear in the display.
Follow steps 6-7 under "TRANSFER
CALLER ID TO AUTODIAL MEMORY" to edit
and save your autodial entry.
1
2
3
PROGRAMMING OPTIONS
1. Ringer Tone
2. Autodialer (see section E)
3. Local Area Code Setting
4. Outside Line
5. Call Waiting Caller ID
6. On-Screen Help
NOTE:
■
If no button is pressed for 30 seconds during
programming functions the LCD will time-out to a
blank display.
PROGRAM OPTION 1:
RINGER TONE
You can select one of 4 ringer tones for the
CP-2070.
Press
PROGRAM.
Press the
UP ARROW KEY
once. The
words “RINGER TONE” and its current
setting (1-4) will be displayed.
Press the
LEFT
or
RIGHT ARROW
KEYS
to select a ringer tone. The CP-
2070 will ring once to confirm the tone you
have selected.
4
Press
PROGRAM
again to finish.
NOTE:
■
The display illustrations in the remainder of this
section are presented with the assumption that your
Caller ID service provides both name and number. If
you have a number-only service, the name will be
blank.
If a caller chooses to partially or completely
“block” Caller ID information, a message will
appear on the display indicating that the name
and/or phone number has been blocked. If, for
any other reason, the name and/or number
information is currently not available from your
local phone company, an “Unavailable” message
will appear on the display. The time and date
information for the call will still be recorded into
the CP-2070’s memory.
F
PROGRAMMING THE CP-2070
1
2
3
4
The CP-2070 can make returning phone calls
easier for users who reside in a 7-digit dialing
area by automatically dialing stored Caller ID
numbers. In order for this feature to work
correctly, it is necessary to program your local
area code into the unit.
PROGRAM OPTION 3:
LOCAL AREA CODE SETTING
Press
PROGRAM
.
Press the
UP ARROW KEY
three times.
The “Area Code” program display will
appear. (000 is the factory default setting).
Use the keypad to enter the three digits of
your local area code.
Press
PROGRAM
again to finish.
If you have the 10 or 11 digit dialing system in
your area, leave the area code setting at 000. The
CP-2070 will prompt you to choose between 7,
10, or 11-digit dialing each time you make a
caller ID call.
1
2
3
4
If your telephone system requires that you enter
an extra digit in order to obtain an outside line,
the CP-2070 can dial this digit for you automa-
tically whenever you dial a stored Caller ID
number. This may be useful if you use your
CP-2070 at a business that uses a PBX telephone
system.
PROGRAM OPTION 4:
OUTSIDE LINE
Press
PROGRAM
.
Press the
UP ARROW KEY
four times.
The “Outside Line” display will appear.
Use the
LEFT
or
RIGHT ARROW KEY
to select a digit.
Press
PROGRAM
again to finish.
The Call Waiting Caller ID option is factory preset
to “OFF.” If you subscribe to Call Waiting Caller
ID, you should set this option to “ON,” otherwise
leave it off.
1
2
3
4
PROGRAM OPTION 5:
CALL WAITING CALLER ID
Press
PROGRAM
.
Press the
UP ARROW KEY
five times.
The “Call Waiting Caller ID” Option display
will appear.
Use the
LEFT
or
RIGHT ARROW KEY
to turn this option ON or OFF.
Press
PROGRAM
again to finish.
1
2
3
4
Two modes of on-screen help are available while
you program the CP-2070. These are:
1. Automatic Help
A help message will automatically scroll
across the screen whenever you wait 15
seconds without pressing a key. If you do not
wish to wait 15 seconds, you can always see
the help message immediately by pressing the
SEND
key.
2. “SEND key” Help
The help messages (with the exception of the
initial message) will not appear unless you
press the
SEND
key.
NOTE:
■
In either mode, you can stop the help message at any
time by pressing any key.
PROGRAM OPTION 6:
ON-SCREEN HELP
TO CHANGE THE HELP
OPTION
Press
PROGRAM
.
Press the
UP ARROW KEY
six times.
The “Help” display will appear.
Use the
LEFT
or
RIGHT ARROW KEY
to switch between the two help modes.
Press
PROGRAM
again to finish.
D
CALL WAITING & CALLER ID
E
AUTODIAL
TONE = for Touchtone systems
PULSE = for Rotary dialing or Pulse systems
5
Select one of the three dialing options and
press
SEND again
. The CP-2070 will
automatically establish a dial tone and
place the call.
