Case CX210C, Руководство по обслуживанию

Страница: 18 / 81

INTRODUCTION
Torque - Special torque settings
Code
Retightening location
Bolt nominal
diameter
Wrench
Tightening torque
1* Travel motor M16 24 mm 267 - 312 N·m ( 196.93 - 230.12 lb ft )
2*
Drive sprocket
M16 24 mm
267 - 312 N·m ( 196.93 - 230.12 lb ft )
3*
Take-up roller
M16 24 mm
267 - 312 N·m ( 196.93 - 230.12 lb ft )
4* Upper roller M20 30 mm 521 - 608 N·m ( 384.27 - 448.44 lb ft )
5* Lower roller M18 27 mm 371 - 432 N·m ( 273.64 - 318.63 lb ft )
6*
Track guard
M18 27 mm
400 - 462 N·m ( 295.02 - 340.75 lb ft )
7
Shoe M20 30 mm
250 - 350 N·m ( 184.39 - 258.15 lb ft )
Tightening angle: 115 - 125 °
8 Counterweight M33 50 mm 1862 - 2058 N·m ( 1373.34 - 1517.90 lb ft )
Outside (29)
M20 30 mm
468 - 545 N·m ( 345.18 - 401.97 lb ft )
9
Turntable
bearing
Inside (36) M20 30 mm 518 - 590 N·m ( 382.06 - 435.16 lb ft )
10* Swing unit M20 30 mm 539.4 - 629.6 N·m ( 397.84 - 464.37 lb ft )
11* Mount M16 24 mm
264.9 - 313.9 N·m ( 195.38 - 231.52 lb ft )
12* Front bracket M10 17 mm
63.8 - 73.6 N·m ( 47.06 - 54.28 lb ft )
13*
Engine
Rear bracket M16 24 mm 205.9 - 247.1 N·m ( 151.86 - 182.25 lb ft )
14 Radiator M16 24 mm 147.2 - 176.6 N·m ( 108.57 - 130.25 lb ft )
15*
Hydraulic
pump
Pump
M20
17 mm
hexagon
socket
head
367 - 496 N·m ( 270.69 - 365.83 lb ft )
16* Hydraulic tank M16 24 mm 232.4 - 276 N·m ( 171.41 - 203.57 lb ft )
17* Fuel tank M16 24 mm
232.4 - 276 N·m ( 171.41 - 203.57 lb ft )
18* Control valve M16 24 mm 267 - 312 N·m ( 196.93 - 230.12 lb ft )
19* Center Lock bar M12 19 mm 88.3 - 107 N·m ( 65.13 - 78.92 lb ft )
20* Joint Joint M12 19 mm
109 - 127 N·m ( 80.39 - 93.67 lb ft )
21 Cab M16 24 mm
149 - 173 N·m ( 109.90 - 127.60 lb ft )
22 Battery M10 17 mm 19.6 - 29.4 N·m ( 14.46 - 21.68 lb ft )
NOTICE: For items marked with *, always apply L
OCTITE
® 262™ or the equivalent and tighten to the specified torque.
The tightening torque in kgf•m is determined with N
・
m ÷ 9.8 ( lbf
・
ft ÷ 7.2 ).
48063128 27/10/2016
11