6 - MAINTENANCE
Torque specifications
Service specifications
Check: Every 250 hours (after the first 50 hours during the run-in period)
At the end of each working day, check all mounting nuts and screws for tightness and tighten if necessary. Make sure
no hardware items are missing. Replace them, if necessary.
Torque specifications per component
Screw
Wrench
Torque setting
Component
(Ø)
mm
in
Nm
lb ft
Travel reduction gear (*)
M16
24
0.9
267–312
197–230
Drive sprocket (*)
M16
24
0.9
267–312
197–230
Idler wheel (*)
M16
24
0.9
267–312
197–230
Upper roller (*)
M16
24
0.9
267–312
197–230
Lower roller (*)
M16
24
0.9
267–312
197–230
Chain guide (*)
M16
24
0.9
267–312
197–230
Track pad
M16
24
0.9
373–451
276–332
Counterweight
M30
46
1.8
1335–1550
985–1143
Turntable
M16
24
0.9
280–312
207–230
Swing reduction gear (*)
M16
24
0.9
280–312
207–230
Engine (*)
M12
19
0.7
109–127
81–93
Engine mount (*)
M16
24
0.9
265–314
196–231
Radiator
M12
19
0.7
64–73
48–54
Hydraulic pump (*)
M16
14 (Hexagon
wrench)
0.6 (Hexagon
wrench)
223–247
165–182
Hydraulic reservoir (*)
M16
24
0.9
233–276
172–203
Fuel tank (*)
M16
24
0.9
233–276
172–203
Control valve (*)
M16
24
0.9
267–312
197–230
Hydraulic swivel (Locking bar)
(*)
M12
19
0.7
89–107
66–78
Hydraulic swivel (Joint) (*)
M12
19
0.7
109–127
81–93
Cab
M16
24
0.9
149–173
110–127
Batteries
M10
17
0.7
20–29
15–21
NOTE:
Use Loctite 262, or the equivalent, on screws marked (*).
6-77
Содержание CX145C SR
