manualshive.com logo in svg

Case 721G Stage IV, Руководство оператора

Поделиться
Скачать
Case 721G Stage IV Скачать руководство пользователя страница 304

7 - MAINTENANCE

Engine oil filter (Initial) - Replace

Replace the engine oil filter when the machine is new and the hourmeter registers 100 hours. Replace the engine oil
filter every 500 hours thereafter or more frequently when the engine operating conditions are severe.

Prior operation:

Keep all non-authorized personnel clear of the area. Park the machine on a firm, level surface in neutral with the
parking brake applied. Lower the bucket/attachment to the ground. Turn off the engine. Install the transport/service
link into the locked position.

NOTE:

it is recommended to change the engine oil when you replace the engine oil filter.

1. Raise the engine hood.

Locate the oil filter

(1)

on the left-hand side of the ma-

chine.
Clean the area around the filter of dirt and debris.

LEIL18WHL1171AA

1

2. Turn the filter housing

(1)

counterclockwise to remove.

Remove and discard the filter following local environ-
mental and waste regulations.

3. Apply a thin layer of clean

CASE AKCELA UNITEK

10W-40

, or the oil needed for operating conditions, to

the new filter gasket.

NOTICE:

never use a filter wrench to install a new filter.

4. Turn the new oil filter onto the base until the gasket

makes contact with the base and then turn by hand an
additional 3/4 turn.

LEIL15WHL1841AB

2

5. Top off

CASE AKCELA UNITEK 10W-40

oil, or the oil

needed for operating conditions, to replace what was
removed with the filter.

6. Lower the engine hood.

7-66

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды