manualshive.com logo in svg

Case 721G Stage IV, Руководство оператора

Поделиться
Скачать
Case 721G Stage IV Скачать руководство пользователя страница 292

7 - MAINTENANCE

Every 10 hours

Engine oil level - Check

WARNING

Entanglement hazard!
Stop the engine and wait for all movement to stop before you open or remove the shield.
Failure to comply could result in death or serious injury.

W1419A

WARNING

Burn hazard!
The engine and exhaust system become hot during operation. To prevent burns, open the engine
compartment and allow the components to cool to a comfortable touch temperature before you work
inside the engine compartment.
Failure to comply could result in death or serious injury.

W1406A

Check the engine oil level every 10 hours or each day, whichever occurs first.

Prior operation:

Keep all non-authorized personnel clear of the area. Park the machine on a firm, level surface in neutral with the
parking brake applied. Lower the bucket/attachment to the ground. Turn off the engine. Install the transport/service
link into the locked position.

Service specifications

Type of oil

CASE AKCELA UNITEK 10W-40
CASE AKCELA UNITEK SSL 0W-40

(cold weather)

Service capacity (with filter change)

15.1 l

(

16.0 US qt

)

1. Open the engine hood.

Locate the engine oil dipstick

(1)

on the right-hand side

of the engine, above the fuel fill location.
Remove the dipstick

(1)

to check the engine oil level.

Wipe the dipstick

(1)

clean and reinsert.

The oil level should register at the full mark.

NOTE:

this procedure is best performed at the beginning

of the work day with the engine cool and all oil drained to
the engine oil pan.

2. Locate the fill location

(2)

in the main engine compart-

ment. Add

CASE AKCELA UNITEK 10W-40

, or the oil

needed for operating conditions, if necessary. Do not
overfill engine oil.

RCPH10WHL899AAH

1

7-54

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды