manualshive.com logo in svg

Case 721G Stage IV, Руководство оператора

Поделиться
Скачать
Case 721G Stage IV Скачать руководство пользователя страница 226

6 - WORKING OPERATIONS

Changing loader attachments

Attachment quick coupler pin engagement
(if equipped)

WARNING

Crushing hazard!
Always use approved attachments. Make sure the attachment is compatible with the machine mount-
ing system.
Failure to comply could result in death or serious injury.

W0183A

WARNING

Falling object hazard!
Before operating the machine, always make sure the bucket or attachment is securely locked into the
quick-attach plate. A loader bucket or attachment that is not securely locked into the quick-attach
plate could come off during loader operation.
Failure to comply could result in death or serious injury.

W0166A

Make certain all unauthorized personnel are clear of the
area when changing attachments. Change attachments
in a flat area clear of obstructions.

Changing attachments

Use the factory/field installed coupler system to change
attachments. Follow procedures in the sections “Coupling
the attachments” and “Uncoupling the attachments” in this
manual.

364917A1_

1

6-4

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды