Case 721G Stage IV Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 522

Case 721G Stage IV Скачать руководство пользователя страница 101

3 - CONTROLS AND INSTRUMENTS

Joystick steering

WARNING

Driving hazard!
If the hydraulic pilots are disengaged, the joystick steering remains active. Always disengage the
joystick steering when not in use.
Failure to comply could result in death or serious injury.

W0449A

WARNING

Driving hazard! Limit the use the Joystick Steering System (JSS) at speeds above 20 km/h (12.4 mph).
Use the Joystick Steering System (JSS) to assist work cycle operations. For optimum control, always
use the primary steering wheel when you operate at higher speeds. Do not use JSS for long travel at
high speeds. When you enable JSS, the maximum machine speed is 30 km/h (18.6 mph).
Failure to comply could result in death or serious injury.

W1514A

WARNING

Driving hazard!
Always use the primary steering when traveling on a public road or highway. The left armrest must be
raised and in a locked position during travel. Do not use joystick steering when traveling on a public
road or highway.
Failure to comply could result in death or serious injury.

W0451A

Joystick steering (optional)

The joystick steering (JSS) allows the operator to steer us-
ing a hand controls located on the left-hand operator seat
armrest. The joystick steering allows for steering move-
ment at the operator’s fingertips.

Use these controls in short cycle, repetitive, high produc-
tion load and carry operations to reduce operator fatigue
and increase operating efficiency.
The system is set up so that the steering wheel is always
usable (it always has priority).
The JSS is not deactivated with steering wheel use. When
the steering wheel is used, the JSS no longer has control.
As soon as the steering wheel is no longer being turned,
the operator is able to go back to using the joystick without
having to reactivate it.

LEIL16WHL1403AB

1

1. Joystick steering (JSS) control lever
2. Joystick steering (JSS) switch

See Chapter 6 - “WORKING OPERATIONS” for further
information.

3-17

«
...
99
100
101
102
103
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды