SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [email protected]
RF Wireless Receiver (Model 0020217 S4X-DC12-ANT3)
Feature:
Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle,
ship, offshore operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens,
locks, motors, fans, winches, blinds, linear actuators, doors, windows, electric solenoid valves, security alarm, business signs and various
devices.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Power Supply: Four different working voltage versions, DC 6V, 9V, 12V, 24V.
DC Power Output: It can control DC equipment with voltage DC 6V / 9V / 12V / 24V.
Each channel can work at maximum current 10A, such as 120W/12V, 60W/6V, 90W/9V, 240W/24V, 1100W/110V, 2200W/220V.
With w
ired control terminal
s: You can connect sensors, limit switches, manual switches or external devices to control the receiver.
With the external antenna, it can have a further working range.
You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Working Range:
With a transmitter (such as CB-4) to form a complete set, the maximum working distance can reach 2000M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it
will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not
reach this maximum working distance.
Receiver Parameters:
Model No.: S4X-DC06-ANT3 / S4X-DC09-ANT3 / S4X-DC12-ANT3 / S4X-DC24-ANT3
Power Supply (Operating Voltage): DC6V (S4X-DC06-ANT3), DC12V±1V (S4X-DC12-ANT3), DC9V±1V (S4X-DC09-ANT3), DC24V±2V
(S4X-DC24-ANT3)
Output: DC6V (S4X-DC06-ANT3), DC12V (S4X-DC12-ANT3), DC9V (S4X-DC09-ANT3), DC24V (S4X-DC24-ANT3)
Working Frequency: 315MHz / 433MHz
Channel: 4 CH
Control Modes: Toggle, Momentary, Latched, Mom Toggle
Static Current: ≤6mA
Maximum Working Current: 10A / each channel
PCB size: 140mm x 73mm x 18mm
Case size: 192mm x 100mm x 45mm
External Telescopic Antenna:
Length of external telescopic antenna: 108mm / 445mm (stretch)
With SMA connector.
If you stretches the external telescopic antenna, it can have a further working range.
Matching Transmitters:
The receiver can work with different transmitters, such as model C-4 (100M), CWB-4 (50M, waterproof), CP-4 (500M), or CB-4 (1000M) etc.
Usage (with the transmitter CB-4):
The receiver can be used to control DC 6V / 9V / 12V / 24V equipments. If the power supply of those equipments is DC 12V, you should choose
the receiver with same DC 12V version; and if the power supply of those equipments is DC 24V, you should choose the receiver with same DC
24V version.
Wiring:
If you want to control the DC 12V lamps, do as following:
1) Connect the positive pole of DC
power supply to terminal “L / +” of INPUT, and connect the negative pole of DC power supply to terminal “N / -”
of INPUT.
2) Connect the positive pole of lamp to terminal "L / +" of OUTPUT, and connect the negative pole of lamp to terminal "N / -" of OUTPUT.
Setting different control modes:
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following):
1) Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle: Press -> On; Press again -> Off.
Press button A: Terminals OUT1 outputs DC power, the lamp 1 is on. Press button A again: Terminals OUT1 stops outputting, the lamp 1 is off.
……
Press button D: Terminals OUT4 outputs DC power, the lamp 4 is on. Press button D again: Terminals OUT4 stops outputting, the lamp 4 is off.
