background image

INSTALLATION INSTRUCTIONS

 

FOR

 

50-0212x-002 SERIES    1181281 
50-0212x-014 SERIES    1181280

 

FORD EXPEDITION

   

OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 

These instructions are intended for use only by experienced professionals in the automotive 
customizing business. Special tools and equipment, as well as specialized handling and care of 
product during installation, may be required. Before beginning this installation, carefully  read 
through the following instructions. 

Use extreme care when cutting headliner material.   

Check for wiring or other componentry above headliner material. Cut only where indicated.

 

 

 

Materials / Tools  required for this installation: 
1. Phillips screwdriver 

2. Powered screwdriver or drill with adapter 

3. Awl or scribe point tool or similar 

4. Razor knife or similar tool 

5. T-10TORX bit driver 

6. 1/8" Drill Bit 

7. Audiovox Series 640/650 Video Module 

  
 

FOR USE IN VEHICLES WITH FACTORY INSTALLED 

OVERHEAD CONSOLE ONLY. 

 
 

Materials provided for this installation:

 

 

INSTALLATION INSTRUCTION # 44-0018D 

         Apr. 14, 1999 
Printed in the U.S.A. 

Содержание 1181280













Отзывы: