Carrier UPC Open Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 30

background image

UPC Open

Carrier Proprietary and Confidential

CARRIER CORPORATION ©2017

Installation and Integration Guide

All rights reserved

1

What is the UPC Open?

The UPC Open (Universal Protocol Converter) is a general purpose protocol converter. The UPC Open can convert

proprietary equipment data into open protocol data, enabling a stand-alone, single piece of equipment to reside

on a BACnet network, where it can be monitored or controlled by a Building Automation System (BAS).

NOTE

A future release of the UPC Open will support installation on a Modbus, N2, or LonWorks network.

UPC Open overview and specifications

«
...
3
4
5
6
7
...
»

Содержание UPC Open































Отзывы:

Нет отзывов

Похожие инструкции для UPC Open

Бренд: Samsung Страницы: 2

Бренд: GCAN Страницы: 16

Бренд: CYP Страницы: 8

Бренд: JTS Страницы: 8

Бренд: Lika Страницы: 2

Бренд: Wagan Страницы: 44

Бренд: C&C TECHNIC Страницы: 2

Бренд: Lika Страницы: 2

Бренд: MediaKind Страницы: 12

HDMI to YUV/YPbPr

Бренд: J.S. Technology Страницы: 2

climatronic converter WMS UP

Бренд: WAREMA Страницы: 4

Wireless Digital Media Player DMP011000-01

Бренд: ActionTec Страницы: 71

Бренд: Kiloview Страницы: 9

Бренд: Xantrex Страницы: 112

Бренд: AXIOMATIC Страницы: 44

LinkTheater LT-H90LAN

Бренд: Buffalo Страницы: 59

Бренд: Roku Страницы: 20

BrightEye 90-FA

Бренд: Ensemble Designs Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды