background image

Installing the UPC Open 

 

 

 

UPC Open 

Carrier Proprietary and Confidential 

CARRIER CORPORATION ©2017   

Installation and Integration Guide 

 

All rights reserved 

 

12 

 

Wire the 

Rnet +

Rnet -

, and 

Gnd 

terminals on the controller's 

Rnet

 port to the terminals of the same name on 

the Wireless Adapter's Rnet connector. 

NOTE  

If using shielded wire, connect the shield wire and the ground wire to the 

Gnd 

terminal.  

 

 

  

Wire the 24 Vac external power supply to the Wireless Adapter's power connector.  

Mount the Wireless Adapter by inserting 2 screws through the mounting tabs on each end of the Wireless 

Adapter. 

Apply power to the external power supply.  

Verify that the LED on top of the Wireless Adapter is blinking. See "LED" below. 

Turn on the controller's power. 

  

LED 

The blue LED on the top of the Wireless Adapter indicates the following: 

   

If the LED is...

 

Then the device...

 

Off 

Is not powered or there is a problem. 

Blinking 

Is working properly. 

Steadily on 

Has a problem. Do one of the following: 

 

Cycle power to the device. 

 

Insert a small screwdriver or paper clip into the hole next to the LED to reboot the 

device. 

 
 
 

 

To wire an Equipment Touch to the UPC Open 

NOTE  

The Equipment Touch requires a 24 Vac power supply. It is not powered by the Rnet. 

 

CAUTION  

Carrier controllers can share a power supply as long as you: 

 

Maintain the same polarity. 

 

Use the power supply only for Carrier controllers. 

  
 

Содержание UPC Open































Отзывы: