Carrier TruVu VVTBP-E2 Скачать руководство пользователя страница 82

Страница: 82 / 92

Appendix A: TV-VVTBP-E2 Points/Properties

TruVu™ VVTBP

-E2

Installation and Start-up Guide

NOTE

Engineering units shown in this document in the defaults and ranges are strictly for reference. You must

enter an integer only.

Status

Navigation:

i-Vu® / Field Assistant:

Properties

Control Program

Status

Point Name/Description

Range

Static Pressure - Prime Variable

–

The current supply duct static pressure. This value is

shown on the default area graphic in i-Vu or Field Assistant.

R: 0 to 2.0 in. H

(0 to .498 kPa)

Supply Air Temperature

–

Airside Linkage Status

Active

, this is the air source’s

current supply air temperature. If

Airside Linkage Status

Not Active

, this value is from

the local SAT sensor.

R: -56 to 245°F

(-48.9 to 118.3°C)

Damper Position

–

Control Device Type

Actuator

, this is the current open damper

position.

R: 0 to 100%

VFD output

–

Control Device Type

VFD

, this is the current VFD speed capacity.

R: 0 to 100%

LAT Control

–

The status of LAT Limit duct static pressure override control of the

bypass.

R: On/Off

LAT Airflow Increase

–

LAT Control

, this is the percent of increase in supply

airflow that the overriding

LAT Duct Static Pressure Setpoint

will provide above the

normal

Controlling Pressure Setpoint

R: 0 to 100%

Unit Configuration

Navigation:

i-Vu® / Field Assistant:

Properties

Control Program

Unit Configuration

Point Name/Description

Default/Range

Control Device Type

–

The device the controller uses to control static pressure.

Actuator

Actuator/VFD drive

Power Fail Restart Delay

–

How long the controller delays normal operation after the

power is restored.

60 seconds

0 to 600 secs

Automatic Deadband Adjustment

–

If using an actuator, set to Enable to automatically

adjust the damper for full travel to correctly scale the damper position. If using a VFD
drive, set to Disable.

Enable

Enable/Disable

Appendix A: TV-VVTBP-E2 Points/Properties

Содержание TruVu VVTBP-E2




























































































Результаты поиска

Содержание TruVu VVTBP-E2

Отзывы:

Похожие инструкции для TruVu VVTBP-E2

Бренды по названию

Популярные бренды

Carrier TruVu VVTBP-E2, Руководство по установке и запуску

Результаты поиска

Содержание TruVu VVTBP-E2

Отзывы:

Похожие инструкции для TruVu VVTBP-E2

Бренды по названию

Популярные бренды