Carrier TruVu VVTBP-E2 Скачать руководство пользователя страница 38

Страница: 38 / 92

Wiring the DAT sensor to the TV-VVTBP-E2's inputs

TruVu™ VVTBP

-E2

Installation and Start-up Guide

You can wire the Duct Air Temperature sensor (Part #33ZCSENDAT) to the TV-VVTBP-E2's inputs.

The TV-VVTBP-E2 must be connected to a Duct Air Temperature (DAT) sensor that monitors the temperature of the
air delivered by the air source.

NOTE

This document gives instructions for wiring the sensors to the TV-VVTBP-E2. For mounting and wiring the

sensor, see the

Carrier Sensors Installation Guide

WARNING

Disconnect electrical power to the TV-VVTBP-E2 before wiring it. Failure to follow this warning

could cause electrical shock, personal injury, or damage to the controller.

CAUTION

•

Do not run sensor or relay wires in the same conduit or raceway with Class 1 AC or DC service wiring.

•

Do not abrade, cut, or nick the outer jacket of the cable.

•

Do not pull or draw cable with a force that may harm the physical or electrical properties.

•

Avoid splices in any control wiring.

Wiring specifications

Cable from sensor to controller:

If <100 ft (30.5 meters) 22 AWG, unshielded
If >100 ft (30.5 meters) 22 AWG, shielded

Maximum length:

500 feet (152 meters)

To wire and mount the DAT sensor

Wire the sensor to the controller's

IN-01

and

Gnd

terminal. See diagram below.

NOTE

Sensor wiring does not have polarity. The wires can be connected to either terminal.

Using electrical tape, insulate any exposed wire to prevent shorting.

Connect shield to earth ground (if using shielded wire to extend cable length).

Wiring the DAT sensor to the TV-VVTBP-E2's inputs

Содержание TruVu VVTBP-E2




























































































Результаты поиска

Содержание TruVu VVTBP-E2

Отзывы:

Похожие инструкции для TruVu VVTBP-E2

Бренды по названию

Популярные бренды

Carrier TruVu VVTBP-E2, Руководство по установке и запуску

Результаты поиска

Содержание TruVu VVTBP-E2

Отзывы:

Похожие инструкции для TruVu VVTBP-E2

Бренды по названию

Популярные бренды