Carrier TruVu VVTBP-E2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 92

background image

Addressing the TV-VVTBP-E2 through the Comm/Service ports

TruVu™ VVTBP

-E2

©2022 Carrier.

Installation and Start-up Guide

All rights reserved.

15

You address the TV-VVTBP-E2 on the controller setup pages. The

Local Network

tab allows you to discover all i-

Vu® XT or TruVu™ devices on a single network and configure them from that page. See

Addressing a network of

controllers using the controller setup Local Network tab

(page 18) and the

Local Network

(page 59) tab.

You can connect the TV-VVTBP-E2 to a computer using a wireless or cable connection to either of the
Comm/Service USB ports.

NOTE

You cannot access the Service port by plugging an Ethernet cable into Eth0 or Eth1.

CAUTION

The USB local access cable provides a common ground connection between the computer and the

controller it connects to. Damage to the controller and possibly the computer’s USB port will occur if the
controller’s input power polarity was not maintained and

was also not properly grounded (floating). If you are not

sure of the wiring polarity and that the controller was properly grounded, use a USB isolator between the computer
and the controller.

To connect the TV-VVTBP-E2 to a computer using the Carrier wireless service adapter.

1

Insert the Carrier wireless service adapter (part# USB-W) into either of the controller's USB Comm/Service
ports to communicate with a Wi-Fi-compatible computer.

2

Open your computer's wireless network display to view your available wireless networks.

NOTE

TV-VVTBP-E2 only supports the 5 GHz band and not the 2.4 GHz band.

3

Connect to the wireless network using the network SSID and password that are printed on the Carrier
wireless service adapter.

4

Open a web browser on the computer and navigate to http://local.access or http://169.254.1.1 to see the
controller setup pages.

Addressing the TV-VVTBP-E2 through the Comm/Service ports

«
...
19
20
21
22
23
...
»

Содержание TruVu VVTBP-E2





























































































Отзывы:

Нет отзывов

Похожие инструкции для TruVu VVTBP-E2

Бренд: IBM Страницы: 144

Бренд: Idesco Страницы: 11

Бренд: B meters Страницы: 2

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 128

VLT DriveMotor FCP 106

Бренд: Danfoss Страницы: 4

Бренд: Gatekeeper Страницы: 28

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

Бренд: mikroElektronika Страницы: 3

Бренд: Window Master Страницы: 7

SaunaLogic SL2 Control

Бренд: Finnleo Страницы: 14

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: Acuity Controls Страницы: 5

Бренд: Risco Страницы: 232

CompleteStat-Series CS9B-THO

Бренд: Bard Страницы: 2

Бренд: NCE Страницы: 4

RISC Module SOM-A2552

Бренд: Advantech Страницы: 40

Бренд: Samson Страницы: 44

Бренд: Beckhoff Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды