Carrier TruVu TV-MPCXP1628-NR Скачать руководство пользователя страница 62

Страница: 62 / 94

Adjusting the TV-MPCXP1628-NR driver properties

TruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

Installation and Start-up Guide

I/O Expanders

The

I/O Expanders

page provides the configuration and status information described in the table below.

I/O Bus Configuration

Maximum I/O Bus Expanders

The control

ler can have no more than 9 TruVu™ MPC I/O

expanders.

Communication Timeout

If the TruVu™ MPC I/O expander does not recei

ve communication from the

controller for this amount of time, the expander will reset itself. The range is 15

–

300 seconds.

I/O Bus Status

The table shows information for all Tr

uVu™ MPC I/O expanders that are

communicating with the TV-MPCXP1628-NR.

Status

Possible statuses

Description

Operational

TruVu™

MPC I/O expander is operating correctly.

Error: Comm Fail

The controller and Tru

Vu™ MPC I/O expander are not

communicating.

Error: Unsupported

Type

The TruVu™

MPC I/O expander type is not compatible

with the controller firmware version.

Disabled

Status briefly shown before

Error: Comm Fail

appears.

Download Required

The version

of firmware in the TruVu™

MPC I/O

expander is different than expander firmware in the TV-

MPCXP1628-NR.

Downloading

The T

ruVu™ MPC I/O expander's firmware is being

upgraded.

Boot Running

Status briefly shown before

Download Required

appears.

Error: Calibration

TruVu™ MPC I/O

expander was not calibrated in the

factory. Please return.

Error: 15V Power

Supply

TruVu™ MPC I

/O expander has detected an issue with

its 15V power supply.

Error: 5V Power Supply

TruVu™

MPC I/O expander has detected an issue with

its 5V power supply.

Input

and

Output Numbers

The number of inputs, HAOs, and outputs on the expander.

FW Version

The version of firmware that is in the expander.

Hardware Type

The number in this column should appear in the list of

Expander Types Supported

in the

I/O Bus Firmware Inventory

section.

Network Termination

Shows if the expander's I/O Bus

End of Net?

switch is set to

Yes

(On) or

(Off).

Model Type

The expander model.

I/O Bus Firmware Inventory

Version

The version of TruVu™ MPC I/O ex

pander firmware that is in the TV-MPCXP1628-

NR.

Expander Types Supported

The TruVu™

MPC I/O expander types supported by the TV-MPCXP1628-NR.

Содержание TruVu TV-MPCXP1628-NR































































































Результаты поиска

Содержание TruVu TV-MPCXP1628-NR

Отзывы:

Похожие инструкции для TruVu TV-MPCXP1628-NR

Бренды по названию

Популярные бренды

Carrier TruVu TV-MPCXP1628-NR, Руководство по установке и запуску

Результаты поиска

Содержание TruVu TV-MPCXP1628-NR

Отзывы:

Похожие инструкции для TruVu TV-MPCXP1628-NR

Бренды по названию

Популярные бренды