Carrier TruVu TV-MPCXP1628-NR Скачать руководство пользователя страница 54

Страница: 54 / 94

Adjusting the TV-MPCXP1628-NR driver properties

TruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

Installation and Start-up Guide

Device

The

Device

page provides the following information plus the items described in the table below:

•

BACnet device object properties for the TV-MPCXP1628-NR

•

The character sets supported by this device for BACnet communication

Configuration

BACnet System Status

The current state of the controller:

Operational
Download in Progress

Download Required
Backup in Progress

Non-Operational

The following fields refer to all networks over which the TV-MPCXP1628-NR communicates.

APDU Timeout

How many milliseconds the device will wait before resending a message if no

response is received.

APDU Segment Timeout

How many milliseconds the device will wait before resending a message segment

if no response is received.

Number of APDU Retries

The number of times the device will resend a message.

Controller Clock

Time Broadcaster will
synchronize time every ____

If you have third-party BACnet devices on one of the router's networks, you can
have the router send a BACnet time sync to those devices at the interval you

define in this field.

Time Synchronization

Recipients

To define third-party BACnet devices as Time Synchronization Recipients:

Click

Add

Select

Device ID

Address

in the

Recipient Type

field.

Enter the

Device ID

Address

information.

Click

Содержание TruVu TV-MPCXP1628-NR































































































Результаты поиска

Содержание TruVu TV-MPCXP1628-NR

Отзывы:

Похожие инструкции для TruVu TV-MPCXP1628-NR

Бренды по названию

Популярные бренды

Carrier TruVu TV-MPCXP1628-NR, Руководство по установке и запуску

Результаты поиска

Содержание TruVu TV-MPCXP1628-NR

Отзывы:

Похожие инструкции для TruVu TV-MPCXP1628-NR

Бренды по названию

Популярные бренды