Carrier TRANSICOLD 69UG15 Series Скачать руководство пользователя страница 21

Страница: 21 / 60

−

T-343

1.10 ENGINE DATA

(Continued)

i. Intake Heater

Amperage

−

42 amps at 12 VDC

Resistance (cold)

−

Approx. 0.3 ohms

j. Horsepower

27 HP @ 1800 RPM at 3000 feet above sea level.

32 HP @ 1800 RPM at sea level.

k. Cooling System

Capacity

6 U.S. quarts (5.68 liters)

−

includes 1 quart (0.95 liter) in

coolant recovery bottle. (Refer to section 4.4.5)

Anti

−

Freeze:

Conventional

The cooling system may be factory charged with a 50/50 mix

of ethylene glycol and water. This mixture provides protection

−

F (

−

C). For replacement, use a low silicate anti

−

freeze meeting GM specifications GM 6038M or equal. Again,

a 50/50 mix is recommended.

Anti

−

Freeze:

Extended Life

The cooling system may be factory charged with a 50/50 mix

of extended life coolant (ELC) and deionized water. This mix-

ture provides protection to

−

F (

−

C). For replacement,

with extended life coolant (ELC) meeting GM specification

GM6277M and deionized water. Again, a 50/50 mix is recom-

mended. Extended life coolant is red or orange in color.

DO NOT

mix with conventional coolant.

Water Temperature

Safety Switch

Setting

Opens

230 +/

−

F (110 +/

−

Resets

200

F (93

−

minimum

Thermostat

Starts to open

177 to 182

F (80 to 84

Fully open

203

F (95

Low Coolant

Sensor

Opens

Closes

Loss of 32 ounces of coolant or more
Refilling of radiator to proper level

l. Lubrication System

Oil Pressure

35 to 60 psig (3.3 to 5.2 kg/cm

)

m. Electrical

Generator

460 VAC (+/

−

10%) @ 60 hz

Содержание TRANSICOLD 69UG15 Series





























































Результаты поиска

Содержание TRANSICOLD 69UG15 Series

Отзывы:

Похожие инструкции для TRANSICOLD 69UG15 Series

Бренды по названию

Популярные бренды

Carrier TRANSICOLD 69UG15 Series, Операция и обслуживание

Результаты поиска

Содержание TRANSICOLD 69UG15 Series

Отзывы:

Похожие инструкции для TRANSICOLD 69UG15 Series

Бренды по названию

Популярные бренды