Carrier Omnizone 09XC06, Инструкция по установке, запуску и обслуживанию

Страница: 14 / 20

14
Table 11 — Condenser Fan Performance — 09XC24 Units
LEGEND
Bhp — Brake Horsepower
ESP — External Static Pressure
NOTES:
1. Units are available with several motor hp options. Refer to Table 2.
2. Static pressure losses for any options or accessories must be
applied to external static pressure before entering the fan perfor-
mance table.
3. Interpolation is permitted; extrapolation is not.
4. Fan performance is based on unit casing, and dry DX (direct
expansion) coil losses at sea level.
SERVICE
Cleaning Condenser Coils
Do not use high-pressure water or air. Damage to fins may result.
Clean coils with a vacuum cleaner, fresh water, compressed air, or
a bristle brush (not wire). Backflush coil to remove debris. Com -
mercial coil cleaners may also be used to help remove grease and
dirt. Steam cleaning is NOT recommended.
Units installed in corrosive environments should be cleaned as
part of a planned maintenance schedule. In this type of applica -
tion, all accumulations of dirt should be cleaned off the coil.
Take care not to get water in the system ducts or unit insulation.
Lubrication
Fan motors have permanently lubricated bearings.
Condenser Fan Adjustment
To prevent personal injury, be sure wire fan guards are secured in
place over each fan discharge (or that fans are ducted) before start -
ing the unit.
TO CHANGE FAN SPEED
1. Shut off unit power supply. Lock out power supply and tag
disconnect locations.
2. Loosen fan belt by loosening fan motor from mounting
bracket. Do not loosen fan motor mounting bracket from unit.
3. Loosen movable pulley flange setscrew (Fig. 7).
CFM
ESP (in. wg)
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70
Rpm Bhp Rpm Bhp Rpm Bhp Rpm Bhp Rpm Bhp Rpm Bhp Rpm Bhp Rpm Bhp
8,500
613 2.20 657 2.54 698 2.87 737 3.22 773 3.56 808 3.91 841 4.27 873 4.63
8,800
634 2.45 677 2.79 717 3.14 755 3.49 790 3.85 824 4.21 857 4.58 889 4.95
9,100
656 2.70 697 3.06 736 3.42 773 3.78 808 4.15 841 4.53 873 4.91 904 5.29
9,400
678 2.98 718 3.35 756 3.72 791 4.09 826 4.47 858 4.86 890 5.25 920 5.64
9,700
699 3.28 738 3.65 775 4.04 810 4.42 844 4.81 876 5.21 907 5.61 936 6.02
10,000
721 3.59 759 3.98 795 4.37 829 4.77 862 5.17 893 5.58 923 5.99 953 6.41
10,300
742 3.92 779 4.32 814 4.73 848 5.14 880 5.55 911 5.97 940 6.39 969 6.82
10,600
764 4.27 800 4.69 834 5.10 867 5.53 898 5.95 928 6.38 958 6.81 986 7.25
10,900
786 4.65 821 5.07 854 5.50 886 5.93 917 6.37 946 6.81 975 7.25 — —
11,200
807 5.04 841 5.48 874 5.92 905 6.36 935 6.81 964 7.26 — — — —
11,500
829 5.46 862 5.91 894 6.36 925 6.81 954 7.27 — — — — — —
11,800
850 5.90 883 6.36 914 6.82 944 7.29 — — — — — — — —
12,100
872 6.36 904 6.83 934 7.30 — — — — — — — — — —
12,400
894 6.84 925 7.32 — — — — — — — — — — — —
12,700
915 7.35 — — — — — — — — — — — — — —
ESP (in. wg)
CFM
0.80 0.90 1.00 1.10 1.20 1.30 1.40
RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
8,500
904 5.00 933 5.37 962 5.75 990 6.13 1017 6.52 1043 6.91 1069 7.30
8,800 919 5.33 948 5.71 976 6.10 1004 6.49 1030 6.89 1056 7.29 — —
9,100
934 5.68 963 6.07 991 6.47 1018 6.87 1044 7.27 — — — —
9,400 949 6.04 978 6.44 1005 6.85 1032 7.26 — — — — — —
9,700
965 6.42 993 6.84 1020 7.26 — — — — — — — —
10,000 981 6.83 1009 7.25 — — — — — — — — — —
10,300
997 7.25 — — — — — — — — — — — —
10,600 — — — — — — — — — — — — — —
10,900
— — — — — — — — — — — — — —
11,200 — — — — — — — — — — — — — —
11,500
— — — — — — — — — — — — — —
11,800 — — — — — — — — — — — — — —
12,100
— — — — — — — — — — — — — —
12,400 — — — — — — — — — — — — — —
12,700
— — — — — — — — — — — — — —