Carrier N92ESN Скачать руководство пользователя страница 27

Страница: 27 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A11157

Fig. 37 – Field-Supplied Isolation Relay for Humidifiers with Internal Power Supply

A200519

Fig. 38 – Thermostat Wiring Diagrams

NOTES FOR THERMOSTAT WIRING DIAGRAMS

1. Refer to outdoor equipment Installation Instructions for additional

information and setup procedure.

2. Outdoor Air Temperature Sensor must be attached in all dual fuel

application.

3. Refer to ICP thermostat Installation Instructions for additional

information and setup procedure.

4. When using a Humidity Sensing Thermostat, set DEHUMIDIFY

OPTIONS to H DE-ENRGZD FOR DEHUM

5. HUM 24VAC terminal is 24 VAC and is energized when the low

pressure switch closes during a call for heat.

6. When connecting 115 VAC to humidifier use a separate 115 VAC

supply.

7. When using a humidifier on a HP installation, connect humidifier to

hot water.

VENTING

NOTE:

Planning for the venting system should be done in conjunction

with planning for the ductwork, drainage, and furnace accessories, such

as air cleaners and humidifiers. Begin assembling the venting system

AFTER

the furnace is set in place in the required orientation.

Venting for this furnace shall follow all Local codes for Category IV

venting systems. This furnace is CSA approved for venting with

PVC/ABS DWV venting systems. This furnace is also CSA approved
for venting with M&G DuraVent

PolyPro

or Centrotherm Innoflue

polypropylene venting systems using single wall straight and flex, and

required fittings (elbows, reducers, increasers, connectors, adapters)

only.

NOTE:

THESE INSTRUCTIONS

DO NOT

CONTAIN DETAILED

INSTALLATION INSTRUCTIONS FOR POLYPROPYLENE

VENTING SYSTEMS. Refer to the polypropylene venting system

manufacturer’s installation instructions for the polypropylene venting

system installation.

NOTE:

When using polypropylene venting systems, all venting

materials used, including the vent terminations, must be from the same

manufacturer.

Special Venting Requirements for Installations in

Canada

Installation in Canada must conform to the requirements of CSA B149

code. Vent systems

must

be composed of pipe, fittings, cements, and

primers listed to ULC S636. The special vent fittings, accessory

concentric vent termination kits and accessory external drain trap

available from the furnace manufacturer have been certified to ULC

S636 for use with those Royal Pipe and IPEX PVC vent components

which have been certified to this standard. In Canada, the primer and

24 V

Coil

To Humidifier Leads

To Com/24V Screw Terminal

on Thermostat Strip

To HUM Terminal On

Furnace Control Board

To Humidifier Leads

Single--Stage Furnace with Single Stage Air

Conditioner

NOTE 9

Single--Stage Furnace with Single--Stage Heat Pump

(Dual Fuel)

NOTE 9

NOTICE

OPTIONAL VENTING BELOW THE FURNACE

The venting system may be positioned below the furnace

ONLY

IF the

factory accessory External Vent Trap Kit is used. The External Vent

Trap Kit is only approved for PVC/ABS DWV venting systems.

CAREFULLY FOLLOW THE INSTRUCTIONS PROVIDED

WITH THE EXTERNAL VENT TRAP KIT FOR LAYING OUT

THE VENTING SYSTEM AND THE DRAIN SYSTEM.

The

instructions included with this furnace

DO NOT APPLY

to vent

systems that are located below the furnace.

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды