Carrier N8MXL Скачать руководство пользователя страница 40

Страница: 40 / 50

Specifications are subject to change without notice.

441 01 1422 00

SERVICE AND MAINTENANCE

PROCEDURES

Untrained personnel can perform basic maintenance functions

such as cleaning and replacing air filters. All other operations

must be performed by trained service personnel. A qualified

service person should inspect the furnace once a year.

FIRE, INJURY, OR DEATH HAZARD

Failure to follow this warning could result in personal

injury, death and/or property damage.
The ability to properly perform maintenance on this

equipment requires certain knowledge, mechanical skills,

tools, and equipment. If you do not possess these, do not

attempt to perform any maintenance on this equipment

other than those procedures recommended in the User’s

Manual.

WARNING

ELECTRICAL SHOCK, FIRE OR EXPLOSION

HAZARD

Failure to follow this warning could result in personal

injury or death.
Before installing, modifying, or servicing system, main

electrical disconnect switch must be in the OFF position and

install a lockout tag. There may be more than one

disconnect switch. Lock out and tag switch with a suitable

warning label. Verify proper operation after servicing.

WARNING

ELECTRICAL OPERATION HAZARD

Failure to follow this caution may result in improper

furnace operation or failure of furnace.
Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous

operation.

CAUTION

INTRODUCTION

GENERAL

These instructions are written as if the furnace is installed in an

upflow application. An upflow furnace application is where the

blower is located below the combustion and controls section of

the furnace, and conditioned air is discharged upward. Since this

furnace can be installed in any of the 4 positions shown in Fig. 4,

you must revise your orientation to component location

accordingly.

ELECTRICAL CONTROLS AND WIRING

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal

injury or death.
There may be more than one electrical supply to the

furnace. Check accessories and cooling unit for additional

electrical supplies that must be shut off during furnace

servicing. Lock out and tag switch with a suitable warning

label.

WARNING

The electrical ground and polarity for 115

−

v wiring must be

properly maintained. Refer to Fig. 25 for field wiring information

and to Fig. 47 for furnace wiring information.

NOTE

: If the polarity is not correct, the STATUS LED on the

control will flash rapidly and prevent the furnace from heating.
The control system also requires an earth ground for proper
operation of the control and flame

−

sensing electrode.

The 24

−

v circuit contains an automotive

−

type, 3

−

amp. fuse

located on the control. (See Fig. 24.) Any shorts of the 24

−

wiring during installation, service, or maintenance will cause this

fuse to blow. If fuse replacement is required, use ONLY a 3

−

amp.

fuse. The control LED will display status code 24 when fuse

needs to be replaced.
Proper instrumentation is required to service electrical controls.

The control in this furnace is equipped with a Status Code LED

(Light

−

Emitting Diode) to aid in installation, servicing, and

troubleshooting. Status codes can be viewed at the sight glass in

blower access door. The furnace control LED is either ON

continuously, flashing a heartbeat, or a status code.
For an explanation of status codes, refer to service label located

on blower access door or Fig. 43 and the troubleshooting guide

which can be obtained from your distributor.
See Fig. 48 for a brief Troubleshooting Guide.

Содержание N8MXL


















































Результаты поиска

Содержание N8MXL

Отзывы:

Похожие инструкции для N8MXL

Бренды по названию

Популярные бренды

Carrier N8MXL, Руководство по установке

Результаты поиска

Содержание N8MXL

Отзывы:

Похожие инструкции для N8MXL

Бренды по названию

Популярные бренды