Carrier Gemini 38AU07 Series Скачать руководство пользователя

Страница: 43 / 52

APPENDIX C — LOW AMBIENT OPTION, FACTORY INSTALLED

Units with the factory installed low ambient option are

equipped with a Motormaster

solid-state head pressure con-

trol which regulates fan speed. A temperature sensor, mount-

ed on either circuit 1 (38AUZ units) or circuit 2 (38AUD

units) of the outdoor coil controls the speed of approved out-

door fan motors in order to maintain a constant head pressure

in the outdoor coil (see Fig. A and Fig. B). The control main-

tains the appropriate head pressure at low ambient tempera-

tures down to –20°F (–28°C).

Wind baffles are required to prevent wind cross currents

from causing abnormally low condensing temperatures.

Use 20-gauge sheet metal to fabricate wind baffles (see

Fig. C and Table A).
OPERATION

Fan on/off control in cooling-only units (38AUZ, 38AUD) is

provided by an outdoor fan relay (OFR). In cooling mode, fan

motor speed of outdoor motors OFM1 and OFM3 is regulated

by the speed control temperature sensor on outdoor coil 1 for a

minimum coil condensing temperature of approximately 100°F

(38°C) at higher outdoor ambient temperature and 80°F (27°C)

at lower ambient. Additionally, outdoor fan motor OFM2 and

OFM4 are turned on/off by the low ambient temperature switch

(LAS), operating the low ambient relay (LAR). The LAS control

temperatures are open 42°F



5 °F, close 57°F



5°F (open 5.5°C



2.8°C, close 13.9°C



2.8°C).

To override the speed control for full fan speed operation

during service or maintenance, either:
a.

remove sensor and place in hot water >120°F (>49°C).

b. rewire to bypass control by connecting speed control

input and output power wires.

Troubleshooting

Speed Control Sensor Resistance

OBSERVATION

POSSIBLE REMEDY

Fans won’t start.

All fans:

Check power and wiring

Check outdoor fan relay (OFR)

OFM1, OFM3 only:

Check speed control sensor location

Check speed sensor resistance

OFM2, OFM4 only:

Check low ambient switch (LAS)

Check low ambient relay (LAR)

Cooling — Center outdoor

fans (OFM2, OFM4) off

below approximately 60°F

(16°C) outdoor ambient.

Normal operation

Cooling — Center outdoor

fans (OFM2, OFM4) not on

above approximately 60°F

(16°C) outdoor ambient.

Check low ambient switch (LAS)

Check low ambient relay (LAR)

Cooling — Slow fan speed

for outer fans (OFM1,

OFM3) at start or during low

outdoor ambient

Normal operation

Cooling — Slow fan speed

for outer fans (OFM1,

OFM3) above 85°F (29°F)

outdoor ambient (should be

full speed)

Check speed control sensor location

Check speed control sensor

resistance

Check fan motor capacitor

Cooling — motor current

into speed control is greater

than motor nameplate FLA

Normal operation

Up to 30% higher A at partial speed at

low ambient

TEMPERATURE

RESISTANCE

°F ± –2°F

°C ± –1°C

Ohms, nominal

–22

–30

88,350

–4

–20

48,485

–10

27,650

16,325

9,950

6,245

5,000

4,028

104

2,663

122

1,801

140

1,244

158

876

Содержание Gemini 38AU07 Series





















































Результаты поиска

Содержание Gemini 38AU07 Series

Отзывы:

Похожие инструкции для Gemini 38AU07 Series

Бренды по названию

Популярные бренды

Carrier Gemini 38AU07 Series, Руководство по установке

Результаты поиска

Содержание Gemini 38AU07 Series

Отзывы:

Похожие инструкции для Gemini 38AU07 Series

Бренды по названию

Популярные бренды