Carrier Gemini 38AU07 Series Скачать руководство пользователя страница 33

Страница: 33 / 52

Fig. 33 — Hot Gas Bypass Option

Fig. 34 — Location of Hot Gas Bypass in 38AUDC12

38AUDC with SVR Relays

With no thermostat demand, there will be no voltage at

LVTB-A1; HGBP SOLENOID is de-energized and solenoid

valve remains closed, preventing bypass vapor from the desu-

perheating tank to enter the suction line at the compressor.

On a thermostat call for first-stage cooling, LVTB terminal

Y1 is powered; when CADM1 is satisfied, compressor con-

tactor C1 and Solenoid Valve Relay SVR1 are energized.

SVR1 contacts close, providing 24-v to LVTB terminal A1,

then through HGBP RELAY NC contacts to HGBP SOLE-

NOID. HGBP solenoid valve opens, allowing bypass vapor

from the desuperheating tank to enter the compressor suction

port.

If thermostat calls for second stage cooling, LVTB termi-

nal Y2 is powered; when CADM2 is satisfied, compressor

contactor C2, Solenoid Valve Relay SVR2 and HGBP RE-

LAY are energized. HGBP RELAY NC contacts open, de-en-

ergizing the HGBP SOLENOID; solenoid valve closes,

blocking bypass vapor from the desuperheating tank and unit

runs at full cooling capacity.

The model 38AUDC also includes the 32LT Motormaster

low ambient control as a standard feature. Refer to Appendix

C for information on the Motormaster control.

All Units

If either the Low Pressure Switch or High Pressure Switch

opens while thermostat output Y1 or Y2 remain energized,

the compressor contactor is de-energized, the compressor

stops and liquid line solenoid is de-energized (valve closes).

CADM initiates a TRIP event (cooling demand sensed at

UCTION LINE

LIQUID LINE

WATCH

YOUR

UCTION

HOT GA

LINE

COMPRE

CONDEN

COIL

EVAPORATOR

COIL

OLENOID

VALVE

HOT GA

BULB

UCTION LINE

AND IN

ULATE

CHRADER VALVE

AT BOTTOM

LIQ INJ BULB
TO

UCTION LINE

HOT GA

DE-

UPERHEAT

CHAMBER

Hot Gas Bypass
Factory Installed
Option

Содержание Gemini 38AU07 Series





















































Результаты поиска

Содержание Gemini 38AU07 Series

Отзывы:

Carrier Gemini 38AU07 Series, Руководство по установке, Страница: 33 / 52

Результаты поиска

Содержание Gemini 38AU07 Series

Отзывы: