background image

FSFXXAOA1180: Installation and User Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

10

TROUBLESHOOTNG

FSF Troubleshooting

A200606

WARNING

!

SHOCK HAZARD

Risk of electric shock. 

Before  performing  any  maintenance  or  servicing,  always  disconnect  the  unit  from  its  power  source  or  turn  power  off  at  service  panel.  Some

troubleshooting steps (boxes in light grey) require the unit to be powered while being manipulated; beware of live and moving parts at all times.

Open the door, set the Run 

me % buon to "Test". 

Does the LED on the 

electronic board light up? 

(The LED is located right next 

to the sensor. Refer to 

Secon 2, step 6. The 

electrical compartment does 

not have to be opened.)

Does the LED on the 

electronic board blink?

Refer to appropriate 

error code according to 

LED blinking.

Plug unit in.

Does the motor 

start?

The unit is working but 

was in a standby period. 

This Supply Fan is 

designed to provide fresh 
air at the best me of the 

day.

Is the unit 

connected to a 

working wall outlet?

Use a small electric 

appliance to test 

the outlet.

Are the J1, J2 and 

J10 connectors well 

connected to the 

board?

Plug unit back. Use 

a voltmeter. Is there 

120 VAC between 

the white wire of J1 

and both sides of 

the fuse? 

Turn the Runme % 

buon at any seng 

other than "Test" for at 

least 5 seconds. Turn the 

buon back to "Test" and 

wait 15 seconds.

Use a voltmeter. Is there 

120 VAC on J2?

Make sure that no 

debris is blocking 

the motor. If there 

is, remove it, 

otherwise replace 

the motor.

Replace the 

electronic 

board.

Use a voltmeter. Is 

there 120 VAC on 

J1?

The power cord may 

be defecve. Call 

customer service.

Replace the 

electronic board

Use a voltmeter. 

Is there 

24 VAC between 

R and C.

Replace the 

electronic 

board.

Verify that the R and C 

connecons are adequate 

and that the low voltage 

source is powered.

unit does not work

YES

YES

NO

YES

NO

Connect the unit 

to a working wall 

outlet.

NO

YES

Restore 

connecons.

NO

YES

YES

NO

NO

YES

NO

YES

NO

YES

NO

FSFXXOA1180

Содержание FSFXXAOA1180















Отзывы: