background image

2

NOTE is used to highlight suggestions which

will

result in

enhanced installation, reliability, or operation.

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could cause personal

injury or death.
Before performing service or maintenance operations

on unit, always turn off main power switch to unit and

install lock(s) and lockout tag(s). Unit may have more

than one power switch. Ensure electrical service to

rooftop unit agrees with voltage an amperage listed on

the unit rating plate.

!

WARNING

CUT HAZARD

Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use

care and wear appropriate protective clothing, safety

glasses and gloves when handling parts and servicing

air conditioning equipment.

CAUTION

!

GENERAL

Identifying Factory Option

NOTE

: This supplement only applies to units that meet

the criteria detailed in Table 1. If the unit does not meet
that criteria, discard this document.

Table 1 – Model--Size / EconoMi$er X Option Indicator

Model / Sizes

Position in

Model Number

EconoMi$er FIOP

Indicator

48/50TC / 08---16

15

U or W

48/50TC / 17---30

15

U, V, W or X

50TCQ / 08---14

15

U or W

50TCQ / 17---24

15

U, V, W or X

48/50HC / 08---14

15

U or W

48/50HC / 17---28

15

U, V, W or X

50HCQ / 08---12

15

U or W

NOTE

: See Fig. 1 for an example of typical Model

Number Nomenclature.
In addition to criteria in Table 1, all units equipped with a

factory--installed EconoMi$er X display a 6 in the 14

th

position of the model number indicating the low leak

economizer controller. These units also display a G in the

17

th

position of the model number to indicate that the unit

is equipped with the factory--installed VFD (Variable

Frequency Drive) option for 2--speed indoor fan control.

The VFD option is required for units equipped with

EconoMi$er X. For detailed information on the VFD see

the Variable Frequency Drive (VFD) Installation, Setup &

Troubleshooting Supplement.

4

8

H

C

D

D

2

4

A

3

A

5

-

6

U

0

G

0

Product Type

Product Series 

1

Example:

Position:

2

3

4

5

6

7

8

9

10 11 12 13

14 15

16

17

18

Sensor Options

Indoor Fan Options & Air Flow Configuraitons

Coil Options (RTPF) (Outdoor - Indoor - Hail Guard)

Electrical Options
G =  2-Speed Indoor Fan (VFD)
  Controller

Heat Options

  

Refrig. Systems Options

Cooling Tons

Packaging

Voltage

Design Revision

Base Unit Controls 

0  =  Base Electromechanical Controls
1 = PremierLink Controller
2  =  RTU Open Multi-Protocol Controller

6  = Electromechanical Controls for Low Leak
  Economizer 

Only

Service Options

Intake / Exhaust Options 

A = None
B =  Temp Economizer w/ Baro Relief
F  =  Enthalpy Econoizer w/ Baro Relief
K =  2 Position Damper

U =  Temp Low Leak Economizer w/ Baro Relief
V =  Temp Low Leak Economizer w/ PE (cent)
W =  Enthalpy Low Leak Economizer 
    w/ Baro Relief
X =  Enthalpy Low Leak Economizer w/ PE (cent) 

C11547

Fig. 1 -- Model Number Nomenclature Example

LLECO

N

--

01

S

I

Содержание EconoMiser X













Отзывы: