Carrier CRECOMZR072A01 Скачать руководство пользователя страница 1

Страница: 1 / 20

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53480313-01

Printed in U.S.A.

Form IIK-CRECOMZR72-03

Pg 1

8-21 Replaces: IIK-CRECOMZR72-02

Installation Instructions

Part No: CRECOMZR072A01 and CRECOMZR073A01

CONTENTS

Page

• BAROMETRIC HOOD (VERTICAL CONFIGURATION)

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

• SUPPLY AIR TEMPERATURE SENSOR (SAT)

• OUTDOOR AIR TEMPERATURE SENSOR (OAT)

• INDOOR AIR QUALITY (CO2) SENSOR

• ENTHALPY SENSORS AND CONTROL

• OUTDOOR AIR ENTHALPY SENSOR/ENTHALPY

CONTROLLER (HH57AC077)

• RETURN AIR ENTHALPY SENSOR (HH57AC078)

• ENTHALPY SWITCH/RECEIVER (33CSENTHSW)

• OUTDOOR ENTHALPY CONTROL REQUIRES ONLY

AN ENTHALPY SWITCH/RECEIVER (33CSENTHSW).

• DIFFERENTIAL ENTHALPY CONTROL REQUIRES

BOTH AN ENTHALPY SWITCH/RECEIVER

(33CSENTHSW) AND AN ENTHALPY SENSOR

(33CSENTSEN).

Power Exhaust   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Demand Controlled Ventilation  . . . . . . . . . . . . . . . . 13
Fire and Smoke Control  . . . . . . . . . . . . . . . . . . . . . . 13
START-UP   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cooling, Units with EconoMi$er 2, PremierLink

Control and a Thermostat . . . . . . . . . . . . . . . . . . 14

• ROUTINE 1 (OAT<DXCTLO)

• ROUTINE 2 (DXCTLO < OAT < 68°F)

• ROUTINE 3 (OAT > 68° F)

Heating, Units with EconoMi$er 2, PremierLink™

Control and a Thermostat . . . . . . . . . . . . . . . . . . 16

Cooling, Units with EconoMi$er2,

PremierLink Control and a Room Sensor . . . . . . 16

Heating Unit with EconoMi$er2, PremierLink Control

and a Room Sensor . . . . . . . . . . . . . . . . . . . . . . . 17

• IF HEATING PID STAGES=2

• IF HEATING PID STAGES=3 AND AUXOUT=HS3

SAFETY CONSIDERATIONS

Installation of this accessory can be hazardous due to system

pressures, electrical components, and equipment location (such as

a roof or elevated structure). Only trained, qualified installers and

service technicians should install, start-up, and service this

equipment.

When installing this accessory, observe precautions in the

literature, labels attached to the equipment, and any other safety

precautions that apply:

• Follow all safety codes

• Wear safety glasses and work gloves

• Use care in handling and installing this accessory

It is important to recognize safety information. This is the safety-

alert symbol:

. When you see this symbol on the unit and in

instructions or manuals, be alert to the potential for personal

injury.

Understand the signal words DANGER, WARNING, CAUTION,

and NOTE. These words are used with the safety-alert symbol.

DANGER identifies the most serious hazards which

will

result in

severe personal injury or death. WARNING signifies hazards

which

could

result in personal injury or death. CAUTION is used

to identify unsafe practices, which

may

result in minor personal

injury or product and property damage. NOTE is used to highlight

suggestions which

will

result in enhanced installation, reliability,

or operation.

GENERAL

The EconoMi$er

2 accessories, with 4 to 20 mA actuator signal

control, do not have a built-in controller. The economizer actuator

is operated by a 4 to 20 mA signal from an existing field-supplied

controller (such as PremierLink™ control). A 12-pin plug is

provided for connection to the control.

Refer to the specific DDC (Direct Digital Controls) literature for

how to indicate

economizer alarm/errors in the building space.

Alarm/error indication may be required for local regulation

compliance.

WARNING

Electrical shock can cause personal injury and death. Shut off

all power to this equipment during installation. There may be

more than one disconnect switch. Tag all disconnect locations

to alert others not to restore power until work is completed.

CAUTION

PERSONAL INJURY HAZARD

Failure to follow this caution can result in personal injury and

damage to the unit.

Cover the duct opening as a precaution so objects cannot fall

into the return duct opening. Be sure to remove the cover when

installation is complete.

IMPORTANT: Read these instructions completely before

attempting to install the accessory economizer.

Medium Rooftop Units

Vertical and Horizontal EconoMi$er

2 Accessory

15 to 27.5 Tons

Содержание CRECOMZR072A01





















Результаты поиска

Содержание CRECOMZR072A01

Отзывы:

Бренды по названию

Популярные бренды

Carrier CRECOMZR072A01, Руководство по установке

Результаты поиска

Содержание CRECOMZR072A01

Отзывы:

Бренды по названию

Популярные бренды